Ankom TDF28 Скачать руководство пользователя страница 7 | Manualshive

Страница: 7 / 10

Ankom TDF28 Скачать руководство пользователя страница 7

In-Line Heater Replacement

(TDF28/28.1)

TDF

ANKOM Technology ● 2052 O’Neil Road ● Email: [email protected] ● Phone: 315-986-8090 ● Fax: 315-986-8091

Service procedure

TS018

Rev. B

6/04/2018

Page 7 of 10

26. On the lower end of the same set of <ed cables

from step 27 above, cable <e the 6 cables to the
1 control box cable. There should be 7 cables
altogether. Carefully trim excess cable <e
without damaging any insula<on.

25. Fasten the white thermistor wire from the In-Line

Heater to the 4 cables from the supply valves and
the  gray  cable  from  the  Pressure  Sensor  with  a
cable  <e.  There  should  be  6  wires  altogether.
Carefully  cut  oﬀ  the  excess  cable  <e  without
damaging any insula<on.

24. Reconnect the J10 connector onto the bo=om

leK prongs on the MUX-T circuit board.

27. Slide two Z462 cable holders onto the In-Line

Heater  cable  (Blue  Arrows).  Insert  the  cable
holders  onto  the  2  PEM  studs  underneath  the
In-Line  Heater  (Red  Arrows).  Screw  the  two
remaining  nuts  back  on,  securing  the  bracket.
make sure the star washers are facing inside.

«
...
5
6
7
8
9
...
»

Содержание TDF28











Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды