Ankom TDF28 Скачать руководство пользователя страница 2 | Manualshive

Страница: 2 / 10

Ankom TDF28 Скачать руководство пользователя страница 2

In-Line Heater Replacement

(TDF28/28.1)

TDF

ANKOM Technology ● 2052 O’Neil Road ● Email: [email protected] ● Phone: 315-986-8090 ● Fax: 315-986-8091

Service procedure

TS018

Rev. B

6/04/2018

Page 2 of 10

6. Detach the white 3-pin connector

labeled “J10” from the MUX-T circuit
board.

5. Remove the 6 tubes going from the

downward  poin<ng  brass  tubes  on
the  In-Line  Heater  to  the  Pressure
Sensor. Only remove the ends of the
tubes  that  are  connected  to  the
Pressure Sensor barbs (Red Arrows).

7. Using a dental pick or a small

screwdriver,  depress  the  tabs  (Black
Arrow)  inside  the  J10  connector  in
order to slide the two conductor out
of  the  terminals  (Red  Arrows).  Set
aside  the  white  J10  connector  for
later use.

8. Loosen the black nut on the explosion

proof

ﬁIng,

located

on

the

underside of the Electrical Enclosure,
that the white thermistor wire runs
through un<l the nut slides oﬀ.

«
1
2
3
4
...
»

Содержание TDF28











Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды