manualshive.com logo in svg

Ankom TDF28, Процедура обслуживания

Поделиться
Скачать
Ankom TDF28 Скачать руководство пользователя страница 1

In-Line Heater Replacement  

(TDF28/28.1) 

TDF 

ANKOM Technology ● 2052 O’Neil Road ● Email: [email protected] ● Phone: 315-986-8090 ● Fax: 315-986-8091

 

Service procedure 

TS018

 

Rev. B 

6/04/2018 

Page 1 of 10 

 

 

4.  Remove the 6 tubes going from the In-Line 

Heater  to  the  Tubing  Support  Panel.  Only 
remove  the  ends  connected  to  the  barbs 
on the Tubing Support Panel (Red Arrows).  

3.  Unscrew  the  6  acorn  nuts  securing  the 

clear  back  plas<c  panel  and  remove.  Set 
aside for rea=achment later. 

1.  Turn  off  the  instrument  and  unplug  the 

power cord. Unscrew the 10 screws on the 
stainless steel back panel and remove. Set 
aside 

the 

panel 

and 

screws 

for                

rea=achment later. 

2.  Unscrew  the  7  screws  on  the  stainless 

steel  top  panel  and  remove.  Set  screws 
and panel aside for rea=achment later. 

To replace an In-Line Heater on the ANKOM      Dietary Fiber Analyzer, follow the steps below. 
 

NOTE: 

The following items will be sent in a replacement package: New In-Line Heater (TDF28 or 

TDF28.1), 18 cable <es (Z10), 1 yellow wire nut (Z139), 4 panel screws (5626), acorn nuts 10/32 
(8409), hex nuts w/ star washer 10/32 (167), white cable holders ¼” (Z462). 

  TDF 

Содержание TDF28











Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды