background image

ANEP BOX-C

Version #1

09/22//2014

11

3.3.3 - Erase a number

 

 

Enter the sequence : « 

#

 » then, the memory number, then « 

#

 »

       

         

Example : Erase the number and memory 

101 

 

#  101  #

         Nota : 

If no key is pressed for over 20 seconds, the unit plays a «

BEEP

»  and  returns  to  the     

                    start of the memory selection part of the programming mode.

3.4 - Memory attribution

3.4.1 - Transfer method  

         

The BOX-C may be programmed to interface with the call center, utilizing the available software and     

         specifications.

         

To communicate with call centers, ANEP unit can transfer its ID information and establish a two-way 

voice communication either :

 

 

• 

In a single calls,

                 

             • 

or two seperate call.

         

 The recommanded method (with respect to European specifications), is to make a single call 

          (the delay time is optimized.

3.4.2  - Programming table for a single call.

       

Telephone N°

Type of data

Type of communication

Call center

Memory # 101

Passenger and tech alarm

Data & audio

Main call center

Memory # 102

Passenger and tech alarm

Data & audio

Backup call center

Memory # 103

Passenger and tech alarm

Data & audio

Backup call center

Memory # 104

Remote end of alarm

Data

Main call center

Memory # 105

Periodic call

Data

Call center for periodics calls

Memory # 106

Alarm data

Data

ANEPanywhere or client call center

Содержание BOX-C

























Отзывы: