4
REMOVING BLADE SET
To remove blade set, first make sure your clipper motor is switched OFF. Push blade release
mechanism under blade hinge (Figure B). While holding down the blade release mechanism, push
down on blade, then gently pull the blade forward (Figure C), and slide it off the blade hinge. If
your blade hinge should snap closed and is flush with the clipper, use a small standard screwdriver
to pry the tongue of the hinge out (Figure D).
NOTE:
Hair may accumulate in the front cavity of the
housing under the blade. If this happens, you can clean out the hair by brushing out the cavity with
a small brush or an old toothbrush while the blade is off the clipper.
REPLACING BLADE SET
To replace or change your blade set, slide the blade bracket onto the hinge of the clipper (Figure E)
and with the clipper turned ON, push the blade towards the clipper to lock into position.
BLADE TEMPERATURE
Due to the high speed nature of Andis clippers, please check for blade heat often, especially on
close cutting blades. If blades are too hot, dip the
blades only
into Andis Blade Care Plus or apply
Andis Cool Care Plus and then Andis Clipper Oil. If you have a detachable blade unit, you can
change your blade in order to maintain a comfortable temperature.
CARE AND SERVICING OF YOUR ANDIS CLIPPER BLADES
Blades should be oiled before,
during
, and after each use. If your clipper blades leave streaks or
slow down, it’s a sure sign blades need oil. Place a few drops of oil on the front and side of the
cutter blades (Figure F). Wipe excess oil off blades with a soft, dry cloth. Spray lubricants contain
insufficient oil for good lubrication, but are an excellent clipper blade coolant. Always replace
broken or nicked blades to prevent injury. You can clean the excess hair from your blades by using
a small brush or worn out toothbrush. To clean the blades, we suggest to immerse the
blades only
into a shallow pan of Andis Clipper Oil, while the clipper is running. Any excess hair and dirt that
has accumulated between the blades should come out. After cleaning, turn your clipper off and
dry blades with a clean dry cloth and start clipping again. If upon cleaning your blades you find
that the blades will still not cut, there may be a few fine pieces of hair trapped between the upper
and lower blade. If this happens, you will need to snap the blade off the clipper. Proceed to slide
the upper blade to one side, without loosening the tension spring or moving the upper blade
completely out from under the tension spring (See Figure G for position of blade). Wipe the
surface between the blades clean with a dry cloth, then place a drop of clipper oil where the upper
and lower blades meet and also in the guide slot of the tension spring (Figure G). Now slide the
upper blade to the opposite side of the lower blade (Figure H) and repeat this process. After
completing this procedure, slide the upper blade, centering it over the lower blade. Handle or
store your Andis clipper with the blades down so excess oil will not run into the clipper case.
FACTORY REPAIR SERVICE
When the blades of your Andis clipper become dull after repeated use, it is advised to purchase a
new set of blades available through your Andis supplier or through an Andis Authorized Service
Station.
CORRECT DISPOSAL OF THIS PRODUCT
This marking indicates that this product should not be disposed with other household
wastes throughout the EU. To prevent possible harm to the environment or human health
from uncontrolled waste disposal, recycle it responsibly to promote the sustainable reuse
of material resources. To return your used device, please use the return and collection
systems or contact the retailer where the product was purchased. They can take this
product for environmental safe recycling.
CAUTION:
Never handle your Andis clipper while you are operating a water faucet and never hold
your clipper under a water faucet or in water. There is danger of electrical shock and damage to
your clipper.
ANDIS COMPANY will not be responsible in case of injury due to this
carelessness.
