Anderson LeakTrac Wireless 2400 Скачать руководство пользователя страница 13

Страница: 13 / 16

2885 Country Drive #190 · St. Paul, MN 55117 · 800-348-1316 · www.leaktools.com

Dealing with “Non-Leak Connections to Ground”:

Although it is always best to remove connections to ground that are not leaks

either physically (as in removing ladders) or by covering (as with light cover), this

is not always possible. There will be situations where the strongest “Leak Track”

in the pool is actually going to a light or stair gasket screw that is not necessarily

leaking. To find leaks in these situations move the probe close to the non-leak

connection to ground, then turn the striped end of the probe away and survey the

vinyl moving away from the non-leak connection. If you pick up a signal pointing

away from the strong non-leak connection it is probably a leak.

In situations where there are other connections to ground such as mentioned

above it will be necessary to survey the entire pool in a tighter pattern than would

be necessary is such other connections were not present.

When checking for leaks in close proximity to “non-leak connections” use the

“low” setting.

Содержание LeakTrac Wireless 2400
















