Analytik Jena PlasmaQuant PQ 9000 Скачать руководство пользователя страница 12

Страница: 12 / 76

Safety instructions

Edition 05/2014

PlasmaQuant PQ 9000

Warning

symbol

Meaning

Remark

Warning of a hazard

location

−

At the extractor device:

Warning of optical radiation. If no exhaust

air hose is connected, it is possible to look

indirectly (by mirror) into the radiation of

the plasma.

−

At the sampling compartment:

Warning of moving parts; warning of hot

torch

−

At the plasma compartment

Warning of hot surfaces.

−

At the power inlet:

Caution when connecting the media

(gases, cooling water and power)

Warning of a hot surface

−

At the plasma compartment:

Warning of hot surfaces. Immediately after

extinguishing the plasma, the surface of

the plasma compartment and in particular

the torch and the plasma chamber window

components and the induction coil are hot.

There is a risk of getting burnt!

Notice symbol

Meaning

Remark

Observe the operating

manual

−

At the power switch:

Before starting work, read the operating

manual.

Before opening the

device, always

disconnect the mains

plug

−

On the side wall at the power inlet:

Before opening the device cover, switch

off the device and disconnect the mains

plug from the mains socket.

The following notice sign is attached to the rear of the PlasmaQuant PQ 9000:

2.4

Requirements for the operating personnel

The PlasmaQuant PQ 9000 must only be operated by qualified specialist personnel instructed

in the use of the device. The instruction must also include conveying the content of this user

manual and the user manuals of other system components.
In addition to the safety at work instructions in this user manual, the generally applicable safety

and accident prevention regulations of the respective country of operation must be observed

and adhered to. The operator must ascertain the latest version of these regulations.

Содержание PlasmaQuant PQ 9000













































































Результаты поиска

Содержание PlasmaQuant PQ 9000

Отзывы:

Похожие инструкции для PlasmaQuant PQ 9000

Бренды по названию

Популярные бренды

Analytik Jena PlasmaQuant PQ 9000, Руководство по эксплуатации

Результаты поиска

Содержание PlasmaQuant PQ 9000

Отзывы:

Похожие инструкции для PlasmaQuant PQ 9000

Бренды по названию

Популярные бренды