background image

ACG+ 
Service & Troubleshooting Manual 

Int. Approved 

Document ref: P0149-825-00 

October 2022 

Page 6 of 37 

 

 

Copyright © 2022 Analox Ltd. All Rights Reserved. 

 
 

Commercial in Confidence 

1

 

Safety information 

 

 

WARNING:  READ THE SAFETY INFORMATION FULLY BEFORE USING THE 

ANALOX ACG+

.

 

 

1.1

 

Electrochemical sensors (oxygen and carbon monoxide) 

 
Electrochemical sensors contain toxic compounds. Under normal conditions the sensor will be safely 
sealed. To prevent leakage, the unit must not be exposed to temperatures outside the specified range, 
or be exposed to organic vapours, which may cause physical damage to the body of the sensor. The 
unit must not be stored in areas containing organic solvents or in flammable liquid stores. 
 
When the life of the sensor has expired or it is leaking or otherwise damaged it must be disposed of 
safely in accordance with local regulations. 
 

The carbon monoxide cell contains an acidic electrolyte (sulphuric acid) whilst the oxygen cell contains caustic 
electrolyte (potassium hydroxide). In the event of an accident, use the following first aid procedures. 
 

Table 1     Electromechanical sensor first aid procedure 

Body 

Part 

Effect 

First Aid Procedures 

Skin 

Contact could result in a chemical 
burn.  
 
Persons with pre-existing skin 
disorders may be more susceptible to 
the effects of the substance. 

Immediately flush the skin thoroughly 
with water for at least 15 minutes.  
 
Remove contaminated clothing and 
wash before re-use.  
 
Obtain medical advice if continued 
irritation. 

Ingestion  Corrosive. May cause sore throat, 

abdominal pain, nausea, and severe 
burns of the mouth, throat, and 
stomach, and may be fatal. 

If swallowed DO NOT INDUCE 
VOMITING.  
 
Wash out mouth thoroughly with 
water and give plenty of water to 
drink.  
 
Obtain medical advice immediately 

Eye 

Persons with pre-existing eye 
problems may be more susceptible to 
the effects of the substance. 
 
Corrosive. May cause redness, pain, 
blurred vision, and eye burns.  
 
Contact can result in the permanent 
loss of sight.  

Irrigate thoroughly with water for at 
least 15 minutes.  
 
Obtain medical advice immediately. 
 
 

Содержание ACG+






































Отзывы: