En-5
1) Filter sign
The indoor unit has a sign to inform the user that it is time to clean the filter.
Select the time setting for the filter sign display interval in the table below
according to the amount of dust or debris in the room. If you do not wish the
filter sign to be displayed, select the setting value for “No indication”.
( ... Factory setting)
Setting description
Function number
Setting value
Standard
11
00
Long interval
01
Short interval
02
No indication
03
The filter sign interval time is different according to Indoor unit type.
Please refer to the installation manual of each indoor unit for details.
FILTER INDICATOR RESET
It lights on if the filter became dirty.
Clean the filter referring to “CLEANING AND CARE (indoor unit operating
manual)”.
After cleaning, press the MANUAL AUTO button (indoor unit) for 2 seconds
or less on the indoor unit.
Indicator Lamp
OPERATION or
TIMER or
ECONOMY or
: Flashing (3 times)
: OFF
2) Static pressure
Select appropriate static pressure according to the installation conditions.
Please refer to the installation manual of each indoor unit for details.
3) Cooler room temperature correction
Depending on the installed environment, the room temperature sensor may
require a correction.
Please refer to the installation manual of each indoor unit for details.
4) Heater room temperature correction
Depending on the installed environment, the room temperature sensor may
require a correction.
Please refer to the installation manual of each indoor unit for details.
5) Auto restart
Enable or disable automatic system restart after a power outage.
( ... Factory setting)
Setting description
Function
number
Setting
value
Yes
40
00
No
01
* Auto restart is an emergency function such as for power failure etc.
Do not start and stop the indoor unit by this function in normal operation.
Be sure to operate by the controller, or external input device.
6) Indoor room temperature sensor switching function
(Only for Wired remote controller)
The following settings are needed when use the control by Wired remote
controller temperature sensor.
( ... Factory setting)
Setting description
Function
number
Setting
value
No
42
00
Yes
01
* If setting value is “00” :
Room temperature is controlled by the indoor unit temperature sensor.
* If setting value is “01” :
Room temperature is controlled by either indoor unit temperature sensor or
remote controller unit sensor.
The air conditioner signal code is set to A prior to shipment. Contact your
retailer to change the signal code.
The remote controller resets to signal code A when the batteries in the
remote controller are replaced. If you use a signal code other than signal
code A, reset the signal code after replacing the batteries.
If you do not know the air conditioner signal code setting, try each of the
signal codes (
) until you find the code which operates the air
conditioner.
STEP 2
SELECTING THE FUNCTION NUMBER AND SETTING VALUE
Refer to the indoor unit installation manual for details on the function
numbers and setting values.
Selecting the Function Number and Setting Value
1
Press the SET TEMP. (
) (
) buttons to select the function number.
(Press the MODE button to switch between the left and right digits.)
2
Press the FAN button to proceed to setting the value.
(Press the FAN button again to return to the function number selection.)
3
Press the SET TEMP. (
) (
) buttons to select the setting value.
(Press the MODE button to switch between the left and right digits.)
4
Press the TIMER MODE button, and START/STOP button, in the order
listed to confirm the settings.
5
Press the RESET button to cancel the function setting mode.
6
After completing the FUNCTION SETTING, be sure to turn off the power
and turn it on again.
10°C HEAT
Function number
Setting value
CAUTION
After turning off the power, wait 10 seconds or more before turning on it
again. The FUNCTION SETTING doesn’t become effective if it doesn’t
do so.
Function Details
Functions
Function
number
Slim duct
1)
Filter sign
11
*1
2)
Static pressure
-
3)
Cooler room temperature
correction
30
4)
Heater room temperature
correction
31
5)
Auto restart
40
6)
Indoor room temperature
sensor switching function
42
7)
Remote controller signal code
44
8)
External input control
46
9)
Room temperature control
switching
48
*1: It is effective only to install IR Receiver unit.
9378626041-03_IM.indb 5
14/5/2555 9:07:13
AMP Air Conditioning
www.ampair.co.uk | [email protected]
