En-4
9.2. Installing the remote controller holder
CAUTION
Check that the indoor unit correctly receives the signal from the remote
•
controller, then install the remote controller holder.
Select the remote controller holder selection site by paying careful
•
attention to the following:
Avoid places in direct sunlight.
Select a place that will not be affected by the heat from a stove, etc.
Install the remote controller with a distance of 5 m between the remote
•
controller and the signal receiver of the receiver unit as the criteria.
However, when installing the remote controller, check that it operates
positively.
Install the remote controller holder to a wall, pillar, etc. with the screw.
•
(1) Mount the Holder.
Screws
(M3
×
12)
(2) Set the Remote Controller.
Insert
Press in
(3)
To remove the Remote Controller (when use at hand).
Slide up
Pull out
10. FUNCTION SETTING
Perform the “FUNCTION SETTING” according to the installation conditions
using the remote controller.
Entering the Function Setting Mode
While pressing the FAN button and SET TEMP. (
•
) simultaneously,
press the RESET button to enter the function setting mode.
STEP 1
Selecting the Remote Controller Signal Code
Use the following steps to select the signal
code of the remote controller. (Note that the air
conditioner cannot receive a signal code if the
air conditioner has not been set for the signal
code.)
The signal codes that are set through this
process are applicable only to the signals in the
FUNCTION SETTING.
For details on how to set the signal codes
through the normal process, refer to 11.
SELECTING THE REMOTE CONTROLLER
SIGNAL CODE.
1
Press the SET TEMP. (
) (
) button to
change the signal code between
.
Match the code on the display to the air conditioner signal code. (initially
set to )
(If the signal code does not need to be selected, press the MODE button
and proceed to STEP 2.)
2
Press the TIMER MODE button and check that the indoor unit can
receive signals at the displayed signal code.
3
Press the MODE button to accept the signal code, and proceed to STEP 2.
PROCEDURE
Please refer to the installation manual of each indoor unit for details.
EXAMPLE
Connect the wires, and then use heat shrink tubing to
protect the connection from dust and water droplets.
Provide a trap in the receiver
unit wiring.
(To prevent water droplets
from entering the receiver unit
and the connector)
If the wiring length is 10m, replace with
receiver unit wire C (optional parts).
Receiver unit wire A 5m
CONNECT
Receiver unit
Heat shrink
tubing
(ø25 L130)
MAX. 10m
Bundle and fasten
the excess wiring.
After shrinking
both ends of
the heat shrink
tubing, seal
the ends with
electrical tape.
Indoor unit
Ceiling
8. TURNING ON THE POWER
1
Turn on the breaker.
2
Make sure that the operation indicator lamp and timer indicator lamp are
slowly flashing alternately.
If the auto restart function has been set, the air conditioner will operate
•
with the settings immediately before the power supply was turned off.
If an error has occurred, the lamps on the receiver unit will flash quickly
•
to indicate the error code. (Referring to
13
of this installation manual)
9. SETTING THE REMOTE CONTROLLER
9.1. Load batteries (R03/LR03 × 2)
1
Press and slide the battery compartment lid on the reverse side to open
it.
Slide in the direction of the arrow while pressing the
mark.
2
Insert batteries.
Be sure to align the battery polarities (
) correctly.
3
Close the battery compartment lid.
CAUTION
Take care to prevent infants from accidentally swallowing batteries.
•
When not using the Remote Controller for an extended period, remove
•
the batteries to avoid possible leakage and damage to the unit.
If leaking battery fluid comes in contact with your skin, eyes, or mouth,
•
immediately wash with copious amounts of water, and consult your
physician.
Dead batteries should be removed immediately and disposed of properly,
•
either in a battery collection receptacle or to the appropriate authority.
Do not attempt to recharge dry batteries.
•
NOTES
Never mix new and used batteries, or batteries of different types.
•
Batteries should last about 1 year under normal use. If the Remote
•
Controller’s operating range becomes appreciably reduced, replace the
batteries and press the RESET button with the tip of a ballpoint pen or
other small object.
10°C HEAT
9378626041-03_IM.indb 4
14/5/2555 9:07:12
AMP Air Conditioning
www.ampair.co.uk | [email protected]
