manualshive.com logo in svg

AML Oceanographic Micro SVT, Руководство пользователя

Поделиться
Скачать
AML Oceanographic Micro SVT Скачать руководство пользователя страница 34

User Manual for AML Oceanographic’s Micro SVT Sensor 

 

34 

 
Insert all three batteries into the brass housing positive end first.  Replace the battery cap on 
the brass housing. 
 
Check the O-ring seals.  The O-rings should be clean, have no nicks, and should be lightly 
greased.    Slide  the  battery  assembly  back  into  the  pressure  case  and  screw  down  the 
retaining ring. 

 

7.2.1  Battery considerations for the Micro SVT 

Care should be observed when choosing replacement lithium batteries for the Micro SVT. 
Battery characteristics such as physical size, current capacity, voltage capacity and 
maximum current sourcing capability should be considered. 
The Micro SVT is shipped with lithium batteries manufactured by SAFT. 
Internet: 

http://www.saftbatteries.com

 

 

7.2.2  Recommended Battery rating for the Micro SVT 

Battery size: C cell 
Voltage capacity: 3.6v 
Amp hour rating: 5.5Ah or better 
Maximum continuous current rating: 800ma or better 
 
Please  refer  to  the  battery  specifications  outlined  in  the  following  documentation  when 
considering a replacement lithium battery for the Micro CTD. 
 

7.2.3  Battery dimensions 

Due  to  the  space  constraints  of  the  Micro  SVT  battery 
assembly  close  attention  to  the  battery  size  must  be 
observed. Dimensions can very from one manufacture to 
another.  The  diagram  shows  the  recommended  size  of 
the lithium batteries for the Micro SVT. 
 

7.2.4  Voltage capacity 

A  nominal  voltage  of  3.6  volts  is  recommended  but 
battery  voltage  will  vary  with  temperature,  usually  the 
lower  the  temperature  the  lower  the  voltage  output  by 
the  battery.  Typically,  lithium  battery  voltage  will  remain  fairly  constant  until  they  are 
near  the  end  of  their  capacity.  When  the  voltage  starts  to  drop  off  rapidly  it  is  a  good 
indication that the batteries need replacing very soon. 
 

7.2.5  Current Capacity 

The  nominal  current  capacity  of  lithium  batteries  will  be  specified  in  Amp  Hours  (Ah) 
and  this  figure  is  used  to  indicate  how  long  the  batteries  will  last.  The  higher  the  Amp 
Hour rating, the longer the battery will last and the more it will cost. Current capacity not 
only  varies  with  temperature,  but  also  with  the  load  (how  much  current  the  instrument 
draws).  
A rough calculation for battery life is hours = Ah/load.  
Where 
  

Hours = hours of battery use 

Содержание Micro SVT












































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды