manualshive.com logo in svg

AML Oceanographic Micro SVT, Руководство пользователя

Поделиться
Скачать
AML Oceanographic Micro SVT Скачать руководство пользователя страница 10

User Manual for AML Oceanographic’s Micro SVT Sensor 

 

10 

4.3 

POWERING THE MICRO SVT SENSOR 

 

4.3.1  External Power 

 

 

The Micro SVT Sensor is normally powered externally via the communications cable. Refer 
to the wiring diagram in Appendix C.  If an AML data cable is used attach the red wire to 
the positive side of the power supply and the black wire to ground.  The power should be a 
DC voltage between 8 and 16 volts, measured at the instrument.  The instrument has reverse 
voltage protection but the instrument will not function if the power leads are connected with 
reverse polarity. 

 

 

Figure 4.3.1   Micro instrument connected to an external power source 

 

4.3.2  Micro SVT logging option 

 
If  the  Micro  SVT  has  been  purchased  with  the  logging  option  it  will  be  equipped  with 
internal memory and an external battery pack.   Refer to the wiring diagram in Appendix 
C.  If the battery pack is used, the instrument is connected to either connector on the battery 
pack  with  an  interconnect  cable.    The  remaining  connector  on  the  battery  pack  is  then 
connected to the data/power cable, which is connected to the computer.  For logging data 
when not connected to the computer the red shorting plug must be inserted into the battery 
pack to turn the power on to the instrument.  Power for the Micro SVT sensor is turned off 
if the there is no shorting plug or data/power cable plugged in to the battery pack. 

 

 

Figure 4.3.2 Micro instrument with battery pack and external sensor connected to an external power 

supply 

Содержание Micro SVT












































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды