AMI 227 Скачать руководство пользователя страница 78

Страница: 78 / 86

MODEL 227

OPERATION MANUAL

Doc # 740063 Rev E

SECTION VII - CALIBRATION

7.6

SYSTEM FAULT CORRECTIONS

When a System Fault occurs prior to or during welding it is required for the operator

to clear the fault condition before welding. When a fault occurs during sequence or

attempting to sequence the FAULT SCREEN will appear.

Some faults are only temporary and the fault is corrected when the arc goes out but all

faults will cause the fault screen to appear and let the operator know why the

sequence was stopped.

The following is a general description of the cause of each type of fault and some

recommendations for correction. In all cases, when the fault is corrected the operator

must press the C key to clear the FAULT SCREEN. If the fault is truly corrected the

system will automatically return to the weld schedule it was on when the fault

occurred.

1. TEMP - The M-227 has internal temperature probes. If the Power Supply gets hot

the a fault occurs. This can occur only if there is some type of blockage of air

circulation, fan failure or component failure within the Power Supply OR THE

SYSTEM IS BEING OPERATED IN AN AMBIENT AIR TEMPERATURE

BEYOND ITS RATED 110 DEGREES F.

This Fault should only occur during an actual weld sequence. If it occurs when

the machine is not welding then a serious internal problem exists. In this case

turn the Power Supply OFF and call an AMI service representative.

If it occurs during welding, check for blockage of the air intakes on the side of the

machine and for cleanliness of the filters. They may need cleaning. If no

blockage exists and the filters are clean then cease all welding operations and call

an AMI Service representative.

2. INPUTAC - Monitors the available line current. If the system cannot supply the

desired DC amperage of the weld schedule it looks to see if the line voltage is

adequate for the amount of current.

7.8

Содержание 227























































































Результаты поиска

Содержание 227

Отзывы:

Бренды по названию

Популярные бренды

AMI 227, Руководство по эксплуатации

Результаты поиска

Содержание 227

Отзывы:

Бренды по названию

Популярные бренды