Ametek Powervar 3400 Series Скачать руководство пользователя страница 57

Страница: 57 / 68

A01-00119 Rev. B

No. Phenomena

Possible Reason

After starting, the

UPS works normally,

but some time later,

the UPS shut down

automatically.

In the status of battery supply power, the

battery is protected for low-voltage caused

by discharging, the system shut down

automatically. The phenomenon is normal.

Once the mains recover, the system will start

automatically and charge for the battery.

Warning: If the battery stays in low-voltage

for long time, it will influence the life span

of battery. After low-voltage protection for

battery, if the mains cannot recover for

long time, it is necessary to disconnect the

battery switch to protect the battery, and

restart the UPS when mains normal, and

charge for the battery.

After the UPS start to

work for a while, the

buzzer beeps intermit-

tently.

The voltage of grid is too low, and the UPS

works in battery inverting status, finally, it

causes the battery low-voltage protection.

When mains normal,

the UPS outputs

normally, when mains

failure, the UPS is

without output.

• Battery fault or the battery group is serious

damaged.

• Charger fault. The charging for battery

cannot be done, which causes the electric

quantity of battery is not enough.

• Battery wire connection is bad or the

connection of terminal is bad.

• The battery switch is not closed.
• After serious overload, the UPS is not re-

started, which causes the UPS always stay

in bypass output status.

The buzzer beeps con-

tinuously, inverter fault

and the UPS turn to

bypass status to supply

power.

• Overload or output is short-circuited, the

UPS shuts down to protect automatically.

•  Drive or power tube is fault.
•  Main controlling board is fault.
•  DC fuse is open-circuit.

Содержание Powervar 3400 Series





































































Результаты поиска

Содержание Powervar 3400 Series

Отзывы:

Бренды по названию

Популярные бренды

Ametek Powervar 3400 Series, Руководство пользователя

Результаты поиска

Содержание Powervar 3400 Series

Отзывы:

Бренды по названию

Популярные бренды