Ametek Powervar 3400 Series Скачать руководство пользователя страница 55

Страница: 55 / 68

A01-00119 Rev. B

No. Phenomena

Fault diagnois and check-

ing points

Solution

The touch screen

and LED are off.

Check if the bypass/ mains

switch is closed and the

power board is fault.

Please inform

professionals to

maintain.

The red ALARM

indicator is on,

and the buzzer

beeps continu-

ously.

Check if the load has a

short-circuit.

Get rid of the

short-circuit point,

close the inverter,

and then restart the

inverter.

Check if the fuse of inverter

is fusing or IGBT module is

abnormal.

Replace the fuse or

IGBT module

Check if AC input is not

present, and the battery is

under low-voltage protection.

It will start

automatically if the

mains normal.

The LOAD

indicator is on in

red.

The output of UPS is

overloaded.

Decrease the load.

When power on

normally, it cannot

output normally.

Check whether the bypass/

inverter SCR drive board is

fault.

Call for service

Communication

abnormal

Communication wiring not

complete

Check wiring

The communication software

is not successfully installed.

Install the software

correctly.

The setting for computer’s

communication window is

wrong.

Properly set the

communication port.

Above problems are all

eliminated, but it still cannot

normally communicate.

Call for service

5.2 Dealing with Common Faults

When starting the UPS, if the UPS cannot work normally, please refer

to Table7-2 to look for reasons. At the same time, please check if it is

caused by external environment, such as temperature, humidity not

meet the requirement or overload.

Содержание Powervar 3400 Series





































































Результаты поиска

Содержание Powervar 3400 Series

Отзывы:

Бренды по названию

Популярные бренды

Ametek Powervar 3400 Series, Руководство пользователя

Результаты поиска

Содержание Powervar 3400 Series

Отзывы:

Бренды по названию

Популярные бренды