manualshive.com logo in svg

Amersham Biosciences Hoefer DALT, Руководство пользователя, Страница: 4 / 70

Поделиться
Скачать
Amersham Biosciences Hoefer DALT Скачать руководство пользователя страница 4

Hoefer DALT System

Amersham Biosciences

Renseignements importants 
d’utilization

Pour une bonne compréhension et une utilisation 
en sécurité maximale, il convient de lire entièrement ce manuel.

Dans la documentation qui accompagne l’instrument un point d’excla-
mation dans un triangle équilatéral a pour but d’attirer l’attention de 
l’utilisateur sur des instructions importantes de fonctionnment ou de 
maintenance.

Tous vos commentaires sur ce manuel seront les bienvenus et veuillez les adresser 
à:

Amersham Biosciences Inc.

Marketing Department
654 Minnesota Street
San Francisco, CA  94107  USA

Amersham Biosciences se réserve le droit d’effectuer des modifications de 

ces spécifications sans aucun préavis.

Garantie et responsabilité

Amersham Biosciences garantit à l’utilisateur que le produit livré a subi 

avec succès tous les essais prévus pour s’assurer qu’il est conforme aux spécifica-
tions et normes en vigueur. La garantie incluse dans les conditions de livraison 
n’est valable que si le produit a été installé et utilisé conformément aux instruc-

tions fournies par Amersham Biosciences.

La société Amersham Biosciences ne sera en aucun cas responsable de 

tout dommage causé directement ou indirectement par toute utilisation incor-
recte ou non approuvée du produit ou découlant de cette utilisation, y compris 
toute perte de bénéfice ou de recettes, toute perte de perspectives commerciales, 
tout empêchement d’utilisation et tout autre risques ayant un rapport avec l’util-
isation du produit, mais sans aucune limitation quant à la nature de ces 
dommages.

© 1998 Amersham Biosciences Limited

. 

Tous droits réservés.

 

La reproduction, le stockage dans un système de récupération d’informations ou 
la transmission sous quelque forme que ce soit et par quelque moyen que ce soit 
de la présente publication en totalité ou en partie sont strictement interdits sans 
autorisation préalable écrite de la société.

Información importante para el usuario

Para comprender el producto y utilizarlo con segu-
ridad es necesario leer este manual en su totalidad.

El signo de admiración en un triángulo 
equilátero en el manual, advierte al usuario sobre la presencia de 
instrucciones importantes de operación y mantenimiento del aparato.

Si desearan hacer algún comentario sobre este manual, tengan la amabilidad de 
remitirlo a:

Amersham Biosciences Inc.

Marketing Department
654 Minnesota Street
San Francisco, CA  94107  USA

Amersham Biosciences se reserva el derecho a modificar las especifica-

ciones sin previo aviso.

Garantía y responsabilidad

Amersham Biosciences garantiza que el producto entregado ha sido pro-

bado a fondo para comprobar el cumplimiento de las especificaciones publica-
das. La garantía incluida en las condiciones de entrega sólo es válida si el 
producto se ha instalado y utilizado de acuerdo con las instrucciones entregadas 

por Amersham Biosciences.

Amersham Biosciences no será responsable, bajo ningún concepto, de

 

daños directos o indirectos, incluyendo sin limitación la pérdida de beneficios, la 
pérdida de ingresos, la pérdida de oportunidades de negocio, la pérdida de uti-
lización y otras consecuencias relacionadas, cualquiera que sea la causa, que se 
deban a la utilización defectuosa e incorrecta del producto.

© 

1998 Amersham Biosciences Limited. Reservados todos 

los derechos.

 

No está permitida la reproducción, ni el almacenaje en un sistema de recuper-
ación, ni la transmisión de parte alguna de esta publicación sin la autorización 
por escrito de la empresa.

Wichtige Benutzerinformationen

Für ein vollständiges Verständnis und eine sichere 
Handhabung dieses Produktes ist es notwendig, daß 
der Benutzer dieses Handbuch vollständig durchliest.

Ein Ausrufezeichen in einem gleichseitigen Dreieck soll den 
Benutzer auf die Anwesenheit wichtiger Betriebs- und Wartungsan-
weisungen in der dem Gerät beiliegenden Dokumentation hin-
weisen.

Wenn Sie Anmerkungen zu diesem Handbuch haben, dann senden Sie diese bitte 
an:

Amersham Biosciences Inc.

Marketing Department
654 Minnesota Street
San Francisco, CA  94107  USA

Amersham Biosciences behält sich das Recht vor, die Spezifikationen 

ohne vorhergehende Ankündigung zu ändern.

Gewährleistung and Haftung

Amersham  Biosciences garantiert, daß das gelieferte Produkt sorgfältig

 

auf die Einhaltung der veröffentlichten Spezifikationen getestet wurde. Die in 
den Lieferbedingungen näher erläuterten Gewährleistungsansprüche gelten nur 

dann, wenn das Produkt gemäß den von Amersham Biosciences 

gelieferten Anweisungen installiert und benutzt wurde.

Amersham Biosciencces übernimmt keinerlei Haftung für Schäden oder

 

Folgeschäden, einschließlich, aber nicht begrenzt auf Gewinneinbußen, Einkom-
mensverluste, entgangene Geschäftsabschlüsse, Verlust der Gebrauchsfähigkeit 
oder andere Verluste, die wie auch immer durch eine fehlerhafte oder 
unsachgemäße Verwendung des Produkts verursacht wurden.

© 1998 Amersham Biosciences Limited.

  

Alle Rechte vorbehalten. 

Die vorliegende Veröffentlichung darf nur mit vorhergehender schriftlicher Gene-
hmigung durch das Unternehmen vervielfältigt, in einem Abrufsystem gespe-
ichert oder in irgendeiner Form oder mit irgendwelchen Mitteln übertragen 
werden.

Informazioni importanti per l’operatore

Per un utilizzo sicuro del prodotto, leggere attentam-
ente l’intero contenuto del presente manuale. 

Il punto esclamativo all’interno di un 
triangolo equilatero indica all’operatore la presenza di importanti 
istruzioni di funzionamento e manutenzione nella documentazione 
allegata al prodotto.

Si prega di inviare eventuali commenti al presente manuale a:

Amersham Biosciences Inc

.

Marketing Department
654 Minnesota Street
San Francisco, CA 94107 USA

A

mersham Biosciecnes si riserva il diritto di apportare modifiche ai dati 

tecnici senza preavviso.

Garanzia e responsabilitá

Amersham Biosciences garantisce che prima della consegna il prodotto è 

stato collaudato a fondo per soddisfare i requisiti specificati. La garanzia inclusa 
nelle condizioni di consegna risulta valida solamente se il prodotto è stato instal-
lato ed utilizzato nel rispetto delle istruzioni fornite da Amersham 

Biosciences

Amersham Biosciences non potrà essere ritenuta responsabile di incidenti 

o danni consequenziali, inclusi’ma non limitati’a perdite di profitti, mancato 
guadagno, perdite di affari, difetti di funzionamento e relative esposizioni, dovuti 
ad un utilizzo non corretto del prodotto.

© 1998 Amersham  Biosciences Limited.

 

Tutti i diritti riservati. 

Nessuna parte della presente pubblicazione può essere riprodotta, conservata in 
sistemi di gestione dati o trasmessa in alcun forma né per nessuno scopo senza 
autorizzazione scritta del produttore.

Français

Español

Deutsch

Italiano

Содержание Hoefer DALT







































































Отзывы:

Нет отзывов