American Megatrends MegaRAC G3 Скачать руководство пользователя страница 129 | Manualshive

Страница: 129 / 151

background image

Appendix C : MegaRAC G3 Remote Recovery Application (RRA)

121

Appendix C

MegaRAC G3 Remote
Recovery Application (RRA)

MegaRAC G3 Card Remote Recovery Application (RRA)

The

Remote Recovery Application (RRA)

is a recovery tool that can be executed from a

remote client system located on the same network as the MegaRAC G3 card. You can use
it to recover a failed flash attempt.

To run the

MegaRAC G3

Remote Recovery Application (RRA)

, double left click on the

RRA.exe

icon.

Note:

You must physically set the MegaRAC G3 card you want to recover into

Recovery Mode

.

To do this, simply short pins two and three on jumper JP12 on your MegaRAC G3 card.

Note:

Your MegaRAC G3 card must be write enabled before you can flash an image to it.
Confirm that pins one and two on jumper JP11 are shorted on your MegaRAC G3 card.

Note:

The firmware upgrade process is a crucial operation. Make sure that the chances of a
power or connectivity loss are minimal when performing this operation.

Button

Description

Card Settings

Left click the

Card Settings

button to configure the MegaRAC G3 card parameters.

Note:

You must configure the card parameters before you start flashing.

Start Flashing

Left click the

Start Flashing

button to begin flashing the firmware image to your

MegaRAC G3 card.

Done

Left click the

Done

button to end the

MegaRAC G3 Remote Recovery Application (RRA)

.

Note:

You must configure the card parameters before you can start flashing your MegaRAC G3
card’s firmware.

Cont’d

«
...
127
128
129
130
131
...
»

Содержание MegaRAC G3
























































































































































Отзывы:

Нет отзывов

Похожие инструкции для MegaRAC G3

Бренд: National Instruments Страницы: 85

Бренд: DAQ system Страницы: 41

Бренд: DAQ system Страницы: 19

Бренд: XNET Страницы: 17

Бренд: Alcatel-Lucent Страницы: 60

FiberTwist XGS2410

Бренд: Genexis Страницы: 7

Blend PRO BP-2002

Бренд: FOLSOM Страницы: 89

VAR-SOM-MX6 HEAT PLATE KIT

Бренд: Variscite Страницы: 3

Бренд: Akasa Страницы: 2

55PUS8118 SCSI-2

Бренд: IBM Страницы: 42

Бренд: MikroTik Страницы: 7

300624 - Ethernet Disk NAS Server

Бренд: LaCie Страницы: 24

Бренд: Tektronix Страницы: 60

Бренд: HighPoint Страницы: 9

Бренд: Alesis Страницы: 44

Бренд: DALRC Страницы: 12

Vector2 Strix RTX 3080 D-RGB

Бренд: EK-Quantum Страницы: 21

Бренд: SELFSAT Страницы: 32

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды