background image

 

29 

 

 

Warranty and Liability Clause

 

 The warranty is extended by American Geothermal Inc. and applies to all commercial equipment and related accessories unless 
otherwise stated.  

The Company warrants for a period of 12 months from initial start-up or 15 months from date of shipment, whichever is less, that 
the Company products covered by this order (1) are free from defects in material and workmanship and (2) have the capacities and 
ratings set forth in the Company’s catalogs and bulletins, provided that no warranty is made against corrosion, erosion, or 
deterioration. The Company’s obligations and liabilities under this warranty are limited to furnishing f.o.b. factory or warehouse at 
Company designated shipping point, freight allowed to Buyer’s city (or port of export for shipment outside the conterminous Unites 
States) replacement equipment (or at the option of the Company parts therefore) for all Company products not conforming to this 
warranty and which have been returned to the manufacturer. The Company shall not be obligated to pay for the cost of lost 
refrigerant. No liability whatever shall attach to the Company until said products have been paid for and then said liability shall be 
limited to the purchase price of the equipment shown to be defective.  

The Company make certain further warranty protection available on an optional extra-cost basis. Any further warranty must be in 
writing, signed by an officer of the Company.  

The warranty and liability set forth herein are in lieu of all other warranties and liabilities, whether in contract or in negligence, 
express or implied, in law or in fact, including implied warranties of merchantability and fitness for particular use. In no event shall 
the Company be liable for any incidental or consequential damages.  

THE WARRANTY AND LIABILITY SET FORTH HEREIN ARE IN LIEU OF ALL OTHER WARRATIES AND LIABILITIES, 
WHETHER IN CONTRACT OR IN NEGLIGENCE, EXPRESS OR IMPLIED, IN LAW OR IN FACT, INCLUDING IMPLIED 
WARRANTIES OF MERCHANTABILITY AND FITNESS FOR PARTICULAR USE, IN NO EVENT SHALL WARRANTOR 
BE LIABLE FOR ANY INCIDENTAL OR CONSEQUENTIAL DAMAGES.  

Содержание CHILLBATCH AMC-20

































Отзывы: