American Dryer Corp. AD-758DV Скачать руководство пользователя

Страница: 19 / 66

IMPORTANT:

Exhaust back pressure measured by a manometer in the exhaust duct

must be

no less

than 0 and

must not exceed

0.3 inches (0.75 mb) of water column (W.C.).

NOTE:

When the exhaust ductwork passes through a wall, ceiling, or roof made of combustible

materials, the opening

must be

2-inches (5.08 cm) larger than the duct (all the way around).

The duct

must be

centered within this opening.

a. Outside Ductwork Protection

1) To protect the outside end of horizontal ductwork from the weather, a 90° elbow bent downward

should be

installed where the exhaust exits the building. If the ductwork travels vertically up

through the roof, it

should be

protected from the weather by using a 180° turn to point the opening

downward. In either case, allow at least twice the diameter of the duct between the duct opening

and the nearest obstruction.

IMPORTANT:

DO NOT

use screens or caps on the outside opening of the exhaust ductwork.

2. Single Dryer Venting

Where possible, it is suggested to provide a separate exhaust duct for each dryer. The exhaust duct

should

laid out in such a way that the ductwork travels as directly as possible to the outdoors with as few turns

as possible. It is suggested that the use of 90° turns in the ducting be avoided; use 30° and/or 45° angles

instead. The shape of the exhaust ductwork is not critical so long as the minimum cross section area is

provided.

IMPORTANT:

Exhaust back pressure measured by a manometer in the exhaust duct

must be

no less

than 0 and

must not

exceed

0.3 inches (0.75 mb) of water column.

Содержание AD-758DV



































































Результаты поиска

Содержание AD-758DV

Отзывы:

Похожие инструкции для AD-758DV

Бренды по названию

Популярные бренды

American Dryer Corp. AD-758DV, Руководство по установке

Результаты поиска

Содержание AD-758DV

Отзывы:

Похожие инструкции для AD-758DV

Бренды по названию

Популярные бренды