background image

Please Note:

 Specifications and improvements in the design 

of this unit and this manual are subject to change without any 

prior written notice.

 X-Move LED 25R                                           Specifications

Model:    

 

X-Move LED 25R

Voltage*: 

 

 

120v/60Hz or 230v/50Hz 

 

LED: 

   1 x 25W CREE LED

Power Consumption: 

75W

Dimensions:    8.75”(L) x 8”(W) x 12.75”(H)

 

 

 

 

221mm x 202mm x 320mm

Beam Angle:   

 

17 Degree

Colors: 

 

 

RGB + White

Weight: 

 

 

14 Lbs. / 6.2 kgs.

Fuse: 

   2 

Amp

Duty Cycle:   

 

None

DMX:   

 

  

9 DMX Channels

Colors:   8 + White

Gobos: 

 

 

6 + Spot

    23.8mm/0.2mm thickness

 

 

 

 

(19mm viewable)

Sound Active:  Yes

Working  Position:   

Any Safe, Secure Position

Warranty: 

 

 

3 Year (1095 days)

*Voltage is user selectable

American DJ

®

  -  www.americandj.com  - X-Move LED 25R Instruction Manual Page 23

©American DJ Supply

American DJ World Headquarters:

6122 S. Eastern Ave. Los Angeles, CA 90040 USA

Tel: 323-582-2650 / Fax: 323-725-6100

Web: www.americandj.com / E-mail: [email protected]

American DJ Europe

Junostraat 2

6468 EW Kerkrade

Netherlands

[email protected] / www.americandj.eu

Tel: +31 45 546 85 00 / Fax: +31 45 546 85 99

Содержание X-Move LED 25R













Отзывы: