background image

©

American DJ

®

  -  www.americandj.com - Emerald Sky™ Instruction Manual Page 11

©

American DJ

®

  -  www.americandj.com - Emerald Sky™ Instruction Manual Page 12

sound activation.

Assigning DMX Address: 

Each dipswitch has a preset value. A spe-

cific DMX address is set by combining the dipswitches that sum your 
desired value. For example: To achieve a DMX address of 7, combine 
dipswitches 1, 2, and 3. Since dipswitch 1 has a value of 1, dipswitch 
2 has a value of 2, and dipswitch 3 has a value of 4, the combination 
of the three create a DMX value of 7. (See example below).

Set DMX address 1:         

Set DMX address 7:

Dip-switches #   1 = 1            

 

Dip-switches #   1 = 1

 

 

 

 

 

 

             2 = 2

 

 

 

 

             

             3 = 4

 

 

 

 

             

       

   = 7

   

 

      

 

 

 

 

Data Cable (DMX Cable) Requirements (For DMX and Master/Slave 
Operation):

 

The Emerald Sky™ can be controlled via DMX-512 proto-

col. The Emerald Sky™ is a two channel DMX unit. The DMX address 
is set on the rear panel of the Emerald Sky.™ Your unit and your DMX 
controller require a standard 3-pin XLR connector for data input and 
data output (Figure 1). If you are making your own cables, be sure to 
use standard two conductor shielded cable (This cable may be pur-
chased at almost all pro sound and lighting stores). Your cables should 
be made with a male and female XLR connector on either end of the 
cable. Also remember that DMX cable must be daisy chained and can 
not be split.

Notice:

 Be sure to follow figures two and three when making your own 

cables. Do not use the ground lug on the XLR connector. Do not con-
nect the cable’s shield conductor to the ground lug or allow the shield 
conductor to come in contact with the XLR’s outer casing. Grounding 
the shield could cause a short circuit and erratic behavior.

DMX512 IN

3-PIN XLR

SOUND

REMOTE

CONTROL

INPUT

POWER

INPUT OUTPUT

SOUND

REMOTE

CONTROL

INPUT

POWER

INPUT OUTPUT

SOUND

REMOTE

CONTROL

INPUT

POWER

INPUT OUTPUT

DMX512

DMX+,DMX-,COMMON

1

2

3

Termination reduces signal errors and

avoids  signal  transmission  problems

and interference. It is always advisable

to connect a DMX terminal, (Resistance

120 Ohm 1/4 W) between PIN 2 (DMX-)

and PIN 3 (DMX +) of the last fixture.

1

2

3

1

2

3

DMX +

DMX -

COMMON

DMX512 OUT

3-PIN XLR

Figure 2

  Emerald Sky™    

 

 

     

             Set Up

Figure 3

1 Ground

1 Ground

XLR Male Socket

XLR Pin Configuration

3 Hot

2 Cold

2 Cold

3 Hot

XLR Female Socket

Pin 3 = Data True (positive)

Pin 2 = Data Compliment (negative)

Pin 1 = Ground

Special  Note:  Line  Termination.

 

When  longer  runs  of  cable  are 

used, you may need to use a terminator on the last unit to avoid erratic 
behavior. A terminator is a 90-120 ohm 1/4 watt resistor which is con-
nected between pins 2 and 3 of a male XLR connector (DATA + and 
DATA -). This unit is inserted in the female XLR socket of the last unit 
in your daisy chain to terminate the line. Using a cable terminator (ADJ 
part number Z-DMX/T) will decrease the possibilities of erratic behav-
ior. 

DMX512 IN

3-PIN XLR

SOUND

REMOTE

CONTROL

INPUT

POWER

INPUT OUTPUT

SOUND

REMOTE

CONTROL

INPUT

POWER

INPUT OUTPUT

SOUND

REMOTE

CONTROL

INPUT

POWER

INPUT OUTPUT

DMX512

DMX+,DMX-,COMMON

1

2

3

Termination reduces signal errors and

avoids  signal  transmission  problems

and interference. It is always advisable

to connect a DMX terminal, (Resistance

120 Ohm 1/4 W) between PIN 2 (DMX-)

and PIN 3 (DMX +) of the last fixture.

1

2

3

1

2

3

DMX +

DMX -

COMMON

DMX512 OUT

3-PIN XLR

Figure 4

5-Pin XLR DMX Connectors.

 

Some manufactures use 5-pin XLR 

connectors for DATA transmission in place of 3-pin. 5-pin XLR fixtures 

may be implemented in a 3-pin XLR DMX line. When inserting stan-
dard 5-pin XLR connectors in to a 3-pin line a cable adaptor must be 
used, these adaptors are readily available at most electric stores. The 
chart below details a proper cable conversion.

Conductor

5-Pin XLR Male (In)

3-Pin XLR Female (Out)

Pin 1

Pin 5 - Do Not Use

Pin 4 - Do Not Use

Pin 3

Pin 2

Pin 1

Pin 3

Pin 2

Not Used

Not Used

Data True (+ signal)

Data Compliment (- signal)

Ground/Shield

3-Pin XLR to 5-Pin XLR Conversion

  Emerald Sky™    

 

 

     

             Set Up

Содержание Emerald Sky











Отзывы: