American access system ADV-1000 Скачать руководство пользователя страница 19

Страница: 19 / 24

Page 19

© American Access Systems

•

Enter the numeral 1 to activate relay A

•

Enter the numeral 2 to activate relay B

Unit will sound a GOOD TONE

DISABLE

the

Event Input

Enter the MASTER CODE

Enter the numeral 9 (Unit will sound Current Mode*)

Enter the numeral 0 to Disable

Unit will sound a GOOD TONE

*Current Modes

Single Tone Indicates:

Remote Inactive Mode is Enabled

Double Tone Indicates:

Arming Circuit Mode is Enabled

Triple Tone Indicates:

Remote Open Mode is Enabled

GOOD TONE Only:

Event Input Disabled

NOTE:

If you

do not

wish to toggle the MODE that the unit reports, enter # to exit.

Erase All Codes -- Sub-Mode 0

Caution: This is a

destructive

Programming Mode. Completing the following steps will erase all

Access Codes except for the factory default Master Code (1 2 5 1). Use with Caution.

DETAILS

This Sub-Mode should rarely be used unless you want to completely erase all Access Codes

entered. This action will not change the Master Code.

To erase all Access Codes and Function Codes

Enter the Master Code (The 1 2 5 1 cannot be deleted)

Enter the numeral 0

Both the Red and Yellow LEDs will flash several times and the unit will sound a GOOD TONE once
all of the memory is cleared.

Enter the Master Code to complete the process

If the sequence is not validated by the unit, you will receive an ERROR TONE and be exited from
this program mode

A GOOD TONE will sound to indicate all memory is cleared.

Содержание ADV-1000

























Результаты поиска

Содержание ADV-1000

Отзывы:

Похожие инструкции для ADV-1000

Бренды по названию

Популярные бренды

American access system ADV-1000, Инструкция по установке и эксплуатации

Результаты поиска

Содержание ADV-1000

Отзывы:

Похожие инструкции для ADV-1000

Бренды по названию

Популярные бренды