background image

 

Version 1.0  

 

©Copyright 2017, Ambient LLC. All Rights Reserved. 

 

 

 

Page 15 

can radiate radio frequency energy and, if not installed and used in accordance with the instructions, 
may cause harmful interference to radio communications.   
However, there is no guarantee that interference will not occur in a particular installation. If this 
equipment does cause harmful interference to radio or television reception, which can be determined 
by turning the equipment off and on, the user is encouraged to try to correct the interference by one or 
more of the following measures:   

 

Reorient or relocate the receiving antenna.   

 

Increase the separation between the equipment and receiver.   

 

Connect the equipment into an outlet on a circuit different from that to which the receiver is 
connected.   

 

Consult the dealer or an experienced radio/TV technician for help.   

 

11.

 

  Warranty Information 

Ambient,  LLC  provides  a  1-year  limited  warranty  on  this  product  against  manufacturing  defects  in 
materials and workmanship. 
 
This limited warranty begins on the original date of purchase, is valid only on products purchased and 
only to the original purchaser of this product. To receive warranty service, the purchaser must contact 
Ambient, LLC for problem determination and service procedures.   
 
Warranty service can only be performed by a Ambient, LLC. The original dated bill of sale must be 
presented upon request as proof of purchase to Ambient, LLC. 
 
Your  Ambient,  LLC  warranty  covers  all  defects  in  material  and  workmanship  with  the  following 
specified exceptions: (1) damage caused by accident, unreasonable use or neglect (lack of reasonable 
and necessary maintenance); (2) damage resulting from failure to follow instructions contained in your 
owner’s manual; (3) damage resulting from the performance of repairs or alterations by someone other 
than an authorized Ambient, LLC authorized service center; (4) units used for other than home use (5) 
applications and uses that this product was not intended (6) the products inability to receive a signal 
due  to  any  source  of  interference  or  metal  obstructions  and  (7)  extreme  acts  of  nature,  such  as 
lightning strikes or floods.   
 
This  warranty  covers  only  actual  defects  within  the  product  itself,  and  does  not  cover  the  cost  of 
installation  or  removal  from  a  fixed  installation,  normal  set-up  or  adjustments,  claims  based  on 
misrepresentation  by  the  seller  or  performance  variations  resulting  from  installation-related 
circumstances. 
 

 

 

Содержание WS-0802
















Отзывы: