background image

 

 

 

 

Fault 

 

EK-S/EK-SH  BAG0022.4  07.22

 

65 

 

11 

Fault 

Fault 

Cause 

Remedy 

Incorrect spread rate. 

Wrong drive speed of the spreading 

disc. 

Maintain the drive speed as 

indicated in the setting chart. 

Setting has not been carried out 

according to the setting chart.  

Carry out the setting accord-

ing to the setting chart.  

Wrong basic shutter slide position.  Check the basic shutter slide 

position. 

Wrong agitator finger position. 

Check agitator finger position. 

Spreading disc drive stops 

Expansion pin on the gearbox input 

is broken due to overload.  
 

Replace expansion pin. 

No material is spread after a pro-

longed transport travel  

Condensed spreading material 

Open the shutter slide com-

pletely, engage the universal 

joint shaft at low tractor rev. 

speed and briefly spread 

stationary. Then again adjust 

the desired spread rate.  

 

Basic shutter slide position 

  1.  Set the shutter slide stop to 17 on the scale 

n. 

  2.  Open shutter slide. 
  3.  Both outlet openings must be 37,5 mm 

open (Fig. 25). 

Agitator finger position 

Check the distance between agitator finger and 

hopper wall. The agitator finger should be paral-

lel to the hopper wall with a distance of 27 + 1 

mm (Fig. 25). 

 

 

Fig. 24 

Replacement of expansion pin 

 

The provided expansion pins serve to replace broken expansion pins 

of the universal joint on the input shaft (overload safety).  
Do not replace broken expansion pins by fitting- or heavy duty expan-

sion pins.  
For fitting only utilise the 8mm hole of the universal joint yoke. The 

10mm hole should only be used to facilitate driving out the broken 

expansion pin. 
Prior to fitting the PTO shaft grease the input shaft! 

 

Содержание EK-S 150













































































Отзывы: