Amazone Catros 3001 Скачать руководство пользователя страница 68

Страница: 68 / 88

Transportation

Catros BAG0053.14 10.17

Catros 4001

The transport position corresponds to the opera-
tional position! No conversion is necessary!

The machine is very wide!

Pay attention to country-specific regu-
lations for road transport!

Catros-2

1. Raise the machine so that there is sufficient

ground clearance to allow unobstructed
folding in.

2. Clean external tools.

3. Actuate control unit

blue

→

Fold in the machine.

4. Clean the central tools.

5. Clean the lighting.

6. Raise the machine so that there is sufficient

ground clearance for transport.

Fig. 49

Folded-in machine in transport position.

Fig. 50

Catros 6002-2:

Note that the maximum transport height is 4 m.

Rear harrow (optional)

WARNING

Before folding the implement

•

Install the transport safety bar
(Fig. 50/3).

Risk of injury due to non-
compliance with the approved
transport width.

•

Catros-2: Lock the tines in posi-
tion 2 with the positioning pins
(Fig. 50/1).

Fig. 51

Содержание Catros 3001

























































































Результаты поиска

Содержание Catros 3001

Отзывы:

Бренды по названию

Популярные бренды

Amazone Catros 3001, Руководство по эксплуатации

Результаты поиска

Содержание Catros 3001

Отзывы:

Бренды по названию

Популярные бренды