manualshive.com logo in svg

Amazone Catros 3001, Руководство по эксплуатации

Поделиться
Скачать
Amazone Catros 3001 Скачать руководство пользователя страница 56

 

 

 

Commissioning 

 

 

56  

Catros  BAG0053.14  10.17 

 

6.1.1.7 

Table  

 

Actual value according to 
calculation 

 

Approved value ac-
cording to tractor 
instruction manual 

 

Double approved 
load capacity (two 
tyres) 

Minimum ballast front / 
rear 

 

/ 

kg 

 

-- 

 

 

-- 

 

 

 

 

   

 

   

Total weight 

 

 

kg 

≤

 

 

kg 

 

-- 

 

 

 

 

   

 

   

Front axle load 

 

 

kg 

≤

 

 

kg 

≤

 

 

kg 

 

 

 

 

   

 

   

 

Rear axle load 

 

 

kg 

≤

 

 

kg 

≤

 

 

kg 

 

 

 

•

 

You can find the approved values for the total tractor weight, 
axle loads and load capacities in the tractor registration papers. 

•

 

The actually calculated values must be less than or equal to ( 

≤

 ) 

the permissible values! 

 

 

WARNING 

Risk of contusions, cutting, catching, drawing in and knocks 
through insufficient stability and insufficient tractor steering and 
brake power. 

It is forbidden to couple the machine to the tractor used as the basis 
for calculation, if 

•

 

One of the actual, calculated values is greater than the approved 
value. 

•

 

There is no front weight (if required) attached to the tractor for 
the minimum front ballast (G

V min

). 

 

 

•

 

Ballast your tractor with weights at the front or rear if the tractor 
axle load is exceeded on only one axle. 

•

 

Special cases: 

ο

 

If you do not achieve the minimum ballast at the front 
(GV min) from the weight of the front-mounted machine 
(GV), you must use ballast weights in addition to the front-
mounted machine. 

ο

 

If you do not achieve the minimum ballast at the rear 
(GH min) from the weight of the rear-mounted machine 
(GH), you must use ballast weights in addition to the rear-
mounted machine. 

 

Содержание Catros 3001

























































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды