![background image](http://html1.mh-extra.com/html/amano/pioneer-eclipse-300bu/pioneer-eclipse-300bu_operators-manual_2918192022.webp)
22
Oil Level Inspection
1. Push machine to level surface.
2. Turn off LP cylinder and remove it.
3. Clean area around the oil gauge before removing it.
4. Remove the oil gauge and wipe it with a paper towel.
5. The machine should be in an upright level position.
If necessary, place a block under the back of the
machine or apply weight to the front of the deck to
maintain an upright, level position.
6. Insert the oil gauge into the tube, but do not tighten
the oil gauge.
7. Check the oil level. It should be between the “FULL”
and “ADD” marks on the oil gauge.
Note: If the oil level is near or below the "ADD" mark,
remove the oil gauge and add enough engine oil to
bring oil level to the "FULL" mark. (Use only Sentinel
Synthetic)
Note: If the oil level is too high, remove the excess oil
by loosening the oil drain valve.
CAUTION!
Do not fill above the "FULL" mark. Excess
oil will cause a smoking condition and may cause the
engine to overheat.
Oil Change
1. Use only Sentinel Synthetic Propane Engine Oil.
Sentinel is specially formulated for small, hot-
temperature engines and provides a longer 250 hour
service interval. If conventional SH or SJ SAE 30 oil
is used instead of Sentinel, scheduled maintenance
MUST revert to every 100 hours to maintain engine
warranty.
2. Change the oil after the first 100 hours of operation
and every 250 hours or 90 days, whichever occurs
first.
3. Start and warm the engine so the oil will drain easily
and completely. Push machine to a level surface.
Stop the engine.
4. Turn off LP cylinder and remove it.
5. Remove cap on the end of oil drain hose.
6. Place a suitable container under the end of the oil
drain hose.
WARNING!
Be careful with hot oil being drained. It
may be hot enough to cause severe burns.
7. Slowly turn the valve counter-clockwise, until the oil
starts to drain.
Note: In order for the oil to drain, it may be necessary
to loosen the oil fill cap.
8. When the oil has finished draining, close the drain
valve and place cap back on the end of the valve.
9. Remove oil cap and add clean Sentinel oil. Use 1.6
U.S. qt. (1.5 L) when the filter is not changed and 1.8
U.S. qt. (1.7 L) when filter is changed.
10. Screw in oil gauge. Reconnect the LP cylinder to the
fuel hose.
11. Run the engine at low idle for 2 minutes. Check for
leaks around the engine.
12. Stop the engine. Check the oil level (see
Oil Level
Inspection
section).
Oil Filter Replacement
1. Place a suitable container underneath the oil filter.
2. Using a strap wrench or oil filter wrench, remove the
oil filter. Turn the filter counter-clockwise to remove
it.
3. Apply a thin coat of new oil or grease to the oil filter
seal (A).
4. Install the new filter
(Part # KA490657007)
by turning
it clockwise.
5. Turn the filter until the seal contacts the mounting
surface (B) of the engine. Then, turn the filter “
BY
HAND”
3/4 turn more.
6. Reconnect the LP cylinder to the fuel hose.
7. Run the engine at low idle for 2 minutes. Check for
leaks around the engine.
Содержание Pioneer Eclipse 300BU
