Amano Pioneer Eclipse 300BU, Руководство оператора, Страница: 20 / 68

20
Machine Troubleshooting
Problem Possible Cause Solution
Propane cylinder is not properly connected. Check connection and open service valve slowly.
Battery is weak. Charge battery or replace.
Oil level is to low. Check the oil level and add if needed.
Place the engine throttle in the idle "slow" position.
Check the regulator vacuum hose for breaks, pinched hose, or a bad connection.
Coil air gap out of adjustment. Adjust coil air gap (Check FS481V Service Manual). Contact an APEC Certified Technician.
Spark plug or head bolts loose. Retorque (Check FS481V Service Manual). Contact an APEC Certified Technician.
Head gasket blown or valves need adjusting
Replace head gasket, adjust valves and replace if necessary (Check FS481V Service
Manual). Contact an APEC Certified Technician.
Propane cylinder is empty. Install properly filled cylinder.
Oil level is to low. Check the oil level and add if needed.
Machine is in the pad change position. Lower the machine to operating position.
Main fuse is blown. Inspect fuse and if blown replace
Place the engine throttle in the idle "slow" position.
Check the regulator vacuum hose for breaks, pinched hose, or a bad connection.
Head gasket blown or valves need adjusting.
Replace head gasket, adjust valves and replace if necessary (Check FS481V Service
Manual). Contact an APEC Certified Technician.
Wires broken or disconnected. Reconnect or replace wires. Contact an APEC Certified Technician.
Coil(s) defective. Replace coil(s) (Check FS481V Service Manual). Contact an APEC Certified Technician.
Spark plug gap is incorrect. Adjust gap to 0.025" (.64mm)
Spark plug defective. Replace spark plug.
If the light is on, turn the key switch off and wait 30 seconds. Try again.
Bad module. Contact an APEC Certified Technician.
Clean or replace the engine dust filter.
Clean or replace the primary filter (paper element).
Clean or repalce the secondary filter (foam element).
Governor out of adjustment or malfunctioning.
Adjust governor and replace if necessary (Check FS481V Service Manual). Contact an
APEC Certified Technician.
Head gasket leaking.
Replace head gasket (Check FS481V Service Manual). Contact an APEC Certified
Technician.
No compression.
Worn piston ring(s) and/or cylinder head(s) require replacement (Check FS481V Service
Manual). Contact an APEC Certified Technician.
Fuel mixture is to lean. Check and adjust fuel mixture if necessary. Contact an APEC Certified Technician.
Valves need adjusting or replacing. Adjust valves (Check FS481V Service Manual). Contact an APEC Certified Technician.
Smell or burned rubber Belt out of adjustment. Check the automatic tensioner
Loose fasteners.
Check the engine, tensioner, spindle, and pad holder fasteners. Tighten any fasteners that
may be loose.
Pad is not centered on the pad holder. Remove pad and re-center on padholder. Replace the pad with a new pad if necessary.
Padholder is out of balance.
Remove pad holder from the macine and clean both sides. Check for cracks or tears.
Replace if necessary.
Wheels are adjusted to far back. Move both wheels forward in the wheel bracket.
Improper pads. Only use recommended burnishing pads.
Bent wheel bracket. Replace wheel bracket.
Wheel is worn or a bad bearing. Replace wheel.
Wheels are adjusted to far back. Move both wheels forward in the wheel bracket.
Propane cylinder is empty. Install properly filled cylinder.
Operator presence switch not engaged.
Engage one of the switch levers while running the machine. Machine will only run for 30
seconds without the one of the switch levers engaged.
Engine oil level is to low. Check the oil level and add if needed.
Dirty air filter(s). Clean both filters or replace if necessary.
Clean all filters or replace if necessary.
Check for any loose wiring or fuel line connections.
Service machine and check the fuel settings. Contact an APEC Certified Technician.
Empty dust bag.
Check the dust scoop and/or the dust tube to see if there is an obstruction.
Skirt is bent or damaged. Replace if necessary.
Adjust the skirt to fit tightly against the seal, but still able to move freely.
Check wear edge on bottom of the skirt and replace if necessary.
Engine is hard to start
Insufficient vacuum.
Engine will not start
Insufficient vacuum.
Econsense shut the machine down
Engine lacks power
Dirty air filter(s).
Dust collection not working
properly
Dust collection bag is not collecting dust.
Skirt is not sealing to the floor.
Machine vibrates
Machine is burnishing too
aggressively
Machine pulls to one side
Engine stops running
Econsense shut the machine down.
Engine stops running
Propane cylinder is empty. Install properly filled cylinder.
Operator presence switch not engaged.
Engage one of the switch levers while running the machine. Machine will only run for 30
seconds without one of the switch levers engaged.
Engine oil level is too low. Check the oil level and add if needed.
Dirty air filter(s). Clean both filters or replace if necessary.
EcoSense shut the machine down
Clean all filteres or replace if necessary.
Check for any loose wiring or fuel line conncetions.
Safe-Stop shut the machine down.
Install properly filled cylinder.
Replace liuid cylinder with vapor cylinder.
Dust collection not working
properly
Dust collection bag is not collecting dust.
Empty the dust bag.
Check the dust scoop and/or the dust tube to see if there is an obstruction.
Skirt is not dealing to the floor.
Skirt is bent or damaged. Replace if necessary.
Adjust the skirt to fit tightly against the seal, but still be able to move freely.
Check wear edge on bottom of the skirt and replace if necessary.