![background image](http://html1.mh-extra.com/html/amano/pioneer-eclipse-300bu/pioneer-eclipse-300bu_operators-manual_2918192017.webp)
17
Fuse
The machine’s electrical circuit is protected by a fuse,
which stops the flow of current in the event of a circuit
overload. Once a fuse blows, it must be replaced. If
the overload that caused the fuse to fail is still present,
the new fuse will fail and the problem must be corrected.
DO NOT
bypass any fuse. The ignition fuse is located
on the side of the starter switch panel.
Dust Bag (Optional)
1. Remove the dust bag by working the elastic over the
lip of the rubber grommet and pulling toward the rear
of the machine.
2. Empty bag by rubbing or gently tapping on sides, in a
downward motion, to loosen soil trapped on sides of
bag. For heavy soil, turn bag inside out to clean.
3. Check the dust tube for debris and clear if needed.
4. Reinstall dust bag by working the elastic band over
the lip of the rubber grommet.
5. Stretch the dust bag towards rear of machine and
orientate with the zipper facing downward.
Dust Box (40” Models)
NOTE: The dust control system of the 420BU40 is
designed to collect the dust generated by the unit when
burnishing a floor. The system in NOT a sweeper unit.
Always pre-sweep floor before burnishing.
1. The dust box does not need to be removed in order
to service the dust filter. To service the dust filter,
remove the thumb screw located on top of the dust
box. The filter can be removed from the filter retainer
and washed. The filter will function wet or dry.
2. To reinstall the filter, correctly place the filter back in
the filter retainer. Insert the bottom edge of the filter
retainer against the metal guide on the bottom of the
mounting area. Compress the filter retainer inward
and downward to align the hole at the top of the
retainer. Install the thumb screw and tighten until the
filter is secured.
3. The dust box should be cleaned daily, but does not
need to be cleaned each time the filter is serviced.
The dust box collects the heavy particles and pad
debris. To remove the dust box, release the latches
that secure the dust box to the unit and slide the dust
box away from the unit.
4. Once the dust box is removed from the unit, remove
the dust filter and service as above. Empty the
dust box into a trash container. The dust box can
be washed if needed. Replace the filter and filter
retainer as above.
5. With the dust box removed, check the opening in the
deck for debris or obstructions. Once the pathway is
clear, reinstall the dust box back on the unit.
Fuse
Содержание Pioneer Eclipse 300BU
