background image

2

WARNING

If the information in these instructions is
not followed exactly, a fire or explosion
may result causing property damage,
personal injury or loss of life.
– Do not store or use gasoline or other

flammable vapors and liquids in the
vicinity of this or any other appliance.

– What to do if you smell gas:

• Do not try to light any appliance.
• Do not touch any electrical switch; do

not use any phone in your building.

• Immediately call your gas supplier

from a neighbor’s phone. Follow the
gas supplier’s instructions.

• If you cannot reach your gas supplier,

call the fire department.

– Installation and service must be

performed by a qualified installer, service
agency or the gas supplier.

WARNING

Should overheating occur or the gas supply
fail to shut off, turn off the manual gas
control valve to the furnace before shutting
off the electrical supply.

To The Owner

It is important that you fill out the owner’s registration card
and mail it today. This will assist Amana in contacting you
should any service or warranty information change in the
future. When filling in the registration card, be sure to
include the Model, Manufacturing and Serial Numbers,
plus the installation date.

Your warranty certificate is also supplied with the unit.
Read the warranty carefully and note what is covered.
Keep the warranty certificate in a safe place, so you can
find it, if necessary.

If additional operating instructions are required, call the
dealer where the purchase was made.

To The Installer

Before installing this unit, please read this manual to
familiarize yourself on the specific items which must be
adhered to, such as maximum external static pressure to
unit, air temperature rise, minimum or maximum CFM,
motor speed connections, and venting. These furnaces
are designed for Category I venting only.

WARNING

To prevent possible death or personal injury
due to asphyxiation, Amana Non-
Condensing Gas Fired Warm Air Furnaces
must be Category I vented. Do not vent any
of these furnaces using Category III venting.

Keep this literature in a safe place for future
reference.

Содержание GCI Series






























Отзывы: