Alutherm heating B350 Скачать руководство пользователя страница 59

Страница: 59 / 60

ALUTHERM

Boilers 59

ALUTERM B 350 - 600

Installation, User and Service Manual

instructions for user

Heating

Alutherm B 350 - 600

Declaration of Conformity van Alutherm Heating.

EC Conformity Declaration

0063CR3475

Alutherm Heating B.V., Craenakker 3a, NL 5951 CC Belfeld, The Netherlands, hereby
declares that the condensing central heating boilers, type

Alutherm B 350-600

Conform to and comply with the essential requirements of the following European
standards and directives.
Regulation/

Description

Date

Directive

(EU) 2016/426

Regulation relating to appliances burning gaseous fuels

09.03.2016

2009/125/EC

Ecodesign Directive (implemented by EU regulation 813/2013)

21.10.2009

2014/35/EU

Low Voltage Directive

26.02.2014

2014/30/EU

Electromagnetic Compatibility Directive

26.02.2014

Relevant harmonized standards:

EN 15502-1

EN 55014-1

EN 61000-3-2

EN 15502-2

EN 55014-2

EN 61000-3-3

EN 60335-2-102

Signed for and behalf of Alutherm Heating B.V.:

G.J.W.Helmes

Belfeld, 2/10/2019

Senior Area Sales Manager

0063

Содержание B350





























































Результаты поиска

Содержание B350

Отзывы:

Alutherm heating B350, Инструкции для пользователя, Страница: 59 / 60

Результаты поиска

Содержание B350

Отзывы: