manualshive.com logo in svg

Alutherm heating B350, Инструкции для пользователя

Поделиться
Скачать
Alutherm heating B350 Скачать руководство пользователя страница 2

ALUTHERM

 | 

Boilers 2

ALUTERM B 350 - 600

 | 

Installation, User and Service Manual

 | 

instructions for user

Heating

Alutherm B 350 - 600

INSTRUCTIONS FOR USER

If you have questions concerning the use of your boiler or heating system, please ask your installer. It is in your own interest and that of the installer 

that you are aware of  how to operate your boiler and heating system safely and efficiently.

The appliance is not to be used by children or persons with reduced physical, sensory or mental capabilities, or lack of experience and knowledge.

Children, even if being supervised, must not play with the appliance

In the case of failure or malfunction of the appliance, do not attempt to repair it yourself. Please contact your installer. Repairs must only be carried 

out by qualified technicians. Failure to comply with these requirements can compromise the safety of the appliance.

Operation

Water, coming from the radiators or from the DHW unit is heated in the aluminium heat exchanger. The CH or DHW pump guarantees  circulation of 

water. The air needed for combustion is sucked in by a rpm controlled fan. At low boiler temperatures the flue gases can be cooled sufficiently for 

condensation of the water.  This water is drained to the sewer via a built in syphon. This drainage must never be blocked. A burner controller with 

built in micro processor provides the electrical control of the boiler.

Topping up

The built in manometer indicates if the waterpressure is sufficient. As soon as the water pressure drops below 1 bar topping up is necessary. If 

topping up becomes a regular ocurrance, your installation should be checked by an installer.

Disconnect from the main. Connect the filling hose to the cold water tap and to the fill and drain valve of the boiler. Before tightning the coupling 

in the installation slowly fill the hose with water allowing any air present to escape. Open the fill and drain valve and slowly fill the installation until a 

pressure between 1.5 and 2.0 bar is reached. When finished connect again to the main.

Bleeding

To remove any air present in the heating system and boiler, bleeding is necessary. Disconnect from the main. Open all the radiator valves. Bleed the 

air from all the radiators starting with the ones at the lowest point in the system. After bleeding, check the water pressure and top-up if required (if 

water pressure has dropped below 1 bar). Connect to the main again.

Starting the boiler

Please ask your installer how to start the boiler. Depending on how your heating system is controlled, this could be via an external timeclock, 

thermostat, switch or otherwise. Once the boiler volt-free enable contacts are closed, the boiler will commence its starting sequence.

Boiler flow temperature

The burner controller can adjust the flow temperature between 20 ° and 85 °C. The temperature setting can be changed using the control panel. 

The installation manual provides the instructions for setting the flow temperature.

DHW (Hot Water) temperature ( if applicable)

From the factory, the DHW temperature is set to a value of 60 °C. This set value can be changed to any value between 35 and 65 °C using the buttons 

on the control panel. If the DHW device has a thermostat the DHW temperature can be adjusted by setting this thermostat.  

Switching off the boiler

During summer time the room thermostat can be set to a lower value to turn off the boiler.  During winter or during a longer period of absence this 

temperature never should be set to a lower value than 15 °C. Don’t switch off the power. During a period of frost all the radiators should be partly or 

totally opened to avoid danger of freezing. 

The integrated pump control will activate the pump every 24 hours for a short period even if no demand is present. This prevents the pump jamming.

Only when work on the boiler is being carried out may the main electricity supply and  gas supply be turned off (your installer can show where these 

are located).

Errors

If an error occurs first check the following

•  Is the room thermostat properly set?

•  Is the boiler connected to the main? Power supply present?

•  Is the gas valve opened?

•  Are the radiator valves open?

•  Is the water pressure in the installation higher than 1 bar?

•  Is the installation bled thoroughly?

An error is indicated by a code on the display. It is very important for the sake of a correct diagnosis to mention this code when calling your installer. 

Reset the burner controller by pressing the ok button on the control panel. If the error occurs frequently contact your installer.

Maintenance

A yearly inspection of the boiler must be done by your installer. The lifespan and the reliability of the installation are improved by doing so.The casing 

of the boiler  may be cleaned with a soft cloth (no abrasives). Never use solvents like thinner!

Caution

The air supply (for air needed for combustion) and the flue parts are essential parts for safe and efficient operation of the boiler. Changes on these 

systems by non qualified persons are not allowed e.g. the settings of the gas valve. The gas/air ratio  is set to a lambda value of approximately 1.26. 

This corresponds with a CO2 level of 9,3 % (full load).

For further information see installation manual.

Содержание B350





























































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды