manualshive.com logo in svg

Alutherm heating B350, Инструкции для пользователя

Поделиться
Скачать
Alutherm heating B350 Скачать руководство пользователя страница 48

ALUTHERM

 | 

Boilers 48

ALUTERM B 350 - 600

 | 

Installation, User and Service Manual

 | 

instructions for user

Heating

Alutherm B 350 - 600

8  

ERRORS

8.1  

General

If there is no data visible on the display, the fuse (10,0 A slow blow) in the control panel near the main switch should be checked (as well as the 

position of the on/off switch) and should if required be replaced (after the cause for break down has been determined and rectified).

WARNING! THIS FUSE IS PART OF THE 230 V CIRCUIT. DISCONNECT THE BOILER FROM THE MAINS ELECTRICITY SUPPLY BEFORE 

REPLACING THE FUSE!

If there is still no data visible on the display, one has to check if there is 230 VAC present on the connections “L” and “N” of  connector X00 in the 

MAXSYS. Also see electrical wiring diagram.

If there is 230 VAC present (terminal connector C1: 19, 20) , then the 230 V fuses F1 and F2  inside the Maxsys should be renewed. Disconnect  the 

boiler from the main 230V supply and remove the connectors from the Maxsys. 

Notice : for this it is not necessary to unscrew the Maxsys from the mounting plate

Release the six security clips with a long thin screw driver. Then remove the  protective cover of the Maxsys. Replace the 230 V fuse(s)  F1: T3.15 AL 

250V  and/or F2  T3.15 AL 250V  inside the Maxsys. 

A blown fuse in the Maxsys controller could be caused by a short-circuited pump. It is recommended to also check the CH-pump and also the DHW 

pump in this case.

If the 230 V fuses  are OK and the display is still blank, then the cable of the display to the Maxsys (X15) should be checked. If this is also ok, the Maxsys 

should be renewed.

 

six security clips

Содержание B350





























































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды