background image

EPH-N00-06003

5-20-97

Page 2 of 11

LIMITED WARRANTY AND REMEDY

A

LUMAX

  B

ATH

  E

NCLOSURES

 warrants to its dealers, customers, and all subsequent purchasers

and users, that the products supplied by it shall be free from material defects in material
and workmanship for a period of one (1) year after shipment, provided they are installed and
maintained according to A

LUMAX

  B

ATH

  E

NCLOSURE

's recommended practices and installation

instructions.  This warranty shall apply only to defects appearing within one (1) year from
the date of shipment, and provided that A

LUMAX

  B

ATH

  E

NCLOSURES

 is promptly notified in

writing of such defects.  The sole and exclusive remedy with respect to the above warranty
or with respect to any other claim relating to defects or any other condition or use of the
products supplied by A

LUMAX

  B

ATH

  E

NCLOSURES

, however caused, and whether such claim

is based upon warranty contract, negligence, strict liability, or any other theory, is limited
to repair or supply of such products, or repayment by A

LUMAX

  B

ATH

  E

NCLOSURES

 of the

purchase price paid for it, at A

LUMAX

  B

ATH

  E

NCLOSURE

's option.

A

LUMAX

  B

ATH

  E

NCLOSURES

 does not make any other representations or warranties, express or

implied, including, but not limited to, any implied warranty of merchantability and any
implied warranty of fitness for a particular purpose.  In no event shall A

LUMAX

  B

A T H

E

NCLOSURES

 be liable for special, direct, indirect, or consequential damages, including, but

not limited to, loss or use of profits.

Dealers agree to pass on to its customers and users in writing A

LUMAX

  B

ATH

  E

NCLOSURE

's

Warranty and Remedy as set forth above.

Laws and building and safety codes governing the design and use of bath enclosures vary
widely.  A

LUMAX

  B

ATH

  E

NCLOSURES

 does not control the selection of product configurations,

operating hardware or glazing materials, and assumes no responsibility therefor.

INSTALLATION NOTES

Unpack your unit carefully and inspect for freight damage.  Lay out and identify all parts
using the instruction sheets as a reference.  Before discarding the carton, check for small
hardware bags that tend to fall to the bottom of the box.  If any parts are damaged or
missing, refer to the descriptions noted in the instructions when contacting your dealer for
r e p l a c e m e n t s .

Handle the glass panels carefully and protect the edges.  Safety tempered glass is very
resistant to breakage, but it can be broken by banging the edges against a hard surface.  The
sharp corners of the panels can damage tile and floor surfaces, so do not remove any
protective devices until you are ready to install the glass.

Please wear safety glasses whenever drilling or cutting.  When drilling holes in ceramic tile
or marble, use a center punch and hammer to carefully break the surface glaze so the drill
can start without skidding.

To install your A

LUMAX

  S

TIKSTALL

 Shower Enclosure you will need the following: tape

measure, level, #2 Phillips screwdriver, drill, 1/8" and 3/16" drill bits, 3/16" wrench,
hacksaw, mallet or hammer, wood block, razor or sharp knife, pencil, glass cleaner, and
caulking (clear silicone recommended).  Optional tools include a miter box for cutting parts
to length, files, center punch and masking tape.

Содержание Stickstall 794 Series












Отзывы: