background image

CD200D II 4-17 All rights reserved © ALTRONIC, LLC 2017

12

12.0 RS-485 COMMUNICATIONS, MODBUS RTU

12.1  The CD200D is compliant to the Modicon Modbus RTU standard. Maximum 

number of registers that can be read at one time is limited to 32. Maximum 

number of booleans that can be read at one time is limited to 256. All com-

munications are 8 data bits, no parity, 1 stop bit. The baud rate is 9600. The 

MODBUS address list follows: 

12.2  24 READ-ONLY STATUS BITS

 

READABLE IN MULTIPLES OF 8 BITS

 

STARTING AT 8-BIT BOUNDARIES

ADDRESS

FUNCTION

10001

Syncing

10002

InSync1

10003

InSync2

10004

Purging

10005

Trying

10006

Firing

10007

LockOut

10008

FIRED

10009

Cranking

10010

Running

10011

Wrong Disk

10012

GLead              Shutdown Grounded

10013

Remote 

Shutdown Present

10014

GLead              Shutdown Logged

10015

Remote           Shutdown Logged

10016

Overspeed     Shutdown Logged

10017

WDOG1 Reset Latched

10018

WDOG2 Reset Event

10019

CheckSum Error

10020

LOW Supply Voltage

10021

No Charge

10022

Open Primary

10023

Shorted Primary

10024

Open Secondary

WARNING: Writable Modbus registers 
such as ‘0XXXX’ and ‘4XXXX’ directly 
reference the CD200D non-volatile 
memory. Non-volatile memory has a 
useful life of ~100,000 Write/Erase 
cycles. Any device writing to these reg-
isters must take care to not exceed the 
maximum number of Write/Erase cycles.

Содержание CD200D

































Отзывы: