manualshive.com logo in svg

Altigen AltiWare ACC 5.1, Руководство администратора, Страница: 365 / 383

Поделиться
Скачать
Altigen AltiWare ACC 5.1 Скачать руководство пользователя страница 365

Appendix B:  Required Service Parameters

AltiWare ACC 5.1 Administration Manual 337

Service Parameters/Request Information for PRI

To subscribe to PRI service, certain parameters are required to establish service. The 
information provided below identifies the recommended and supported parameters for 
PRI service. When ordering PRI service, provide the following service request 
information:

Equipment Information

•

PBX Manufacturer—AltiGen Communications, Inc.

•

CSU/DSU—ADTRAN T1 ACE (recommended) or other CSU/DSU

Technical Information for PRI with Voice

Switch Type:

•

5ESS (recommended) 

•

DMS (recommended) 

•

NI-2 (recommended) 

•

4ESS

•

MEGACOMM

Framing:

•

Super Frame (SF)/D4

•

Extended Super Frame (ESF) (recommended)

Line Coding:

•

Alternate Mark Inversion (AMI)

•

B8ZS (recommended)

Physical Termination: 

•

RJ-48X or RJ-48C

Wire: 

•

4 wires

PRI Channel Assignment

D Channels Assignment—24th channel (channel ID 23)

Note:

AltiWare ACC/ACM can configure any channel in a PRI span to be the D 
channel. The default setting is the last channel. Every span should select a D 
channel within the span. Shared D channel (NFAS) or back up D channel is 
not supported.

Hunting—Most Idle, Least Idle, Ascend, Descend
DNIS Digits—can be 3 to 10 digits

CSU/DSU Requirements

The CSU (channel service unit) is a device used to connect a digital trunk line coming in 
from the phone company to the PBX. A CSU can terminate signals, repeat signals, and 
respond to loopback commands sent from the central office.

Содержание AltiWare ACC 5.1
































































































































































































































































































































































































Отзывы:

Нет отзывов