Altera Stratix 10 GX FPGA Скачать руководство пользователя страница 11

Страница: 11 / 97

3. Set DIP switch bank (SW6) to match the following table.

Table 5.

SW6 JTAG Bypass DIP Switch Default Settings (Board Bottom)

Switch

Board Label

Function

Default Position

Intel Stratix 10

OFF to enable the Intel

Stratix 10 in the JTAG chain.
ON to bypass the Intel

Stratix 10 in the JTAG chain.

OFF

MAX V

OFF to enable the MAX V in

the JTAG chain.
ON to bypass the MAX V in

the JTAG chain.

OFF

FMC

OFF to enable the FMC

Connector in the JTAG chain.
ON to bypass the FMC

connector in the JTAG chain.

4. SW1 DIP Switch Default Settings (Board TOP)

Table 6.

SW1 DIP Switch Default Settings (Board TOP)

Switch

Board Label

Function

MSEL2

MSEL2, MSEL1 = [0,0] QSPI AS Fast

Mode
MSEL2, MSEL1 = [0,1] QSPI AS

Normal Mode
MSEL2, MSEL1 = [1,0] AVST x16 Mode

(Default)
MSEL2, MSEL1 = [1,1] JTAG Only Mode

MSEL1

5. Set DIP switch bank (SW6) to match the following table.

Table 7.

SW3 DIP Switch Default Settings (Board Bottom)

Switch

Board Label

Function

Default Position

CLK0_OEn

ON to enable the Si5341A

clock device
OFF to disable the Si5341A

clock device

CLK0_RSTn

ON to hold the Si5341A

clock device in reset
OFF to allow the Si5341A

clock device to function

normally

OFF

FACTORY_LOAD

ON to load factory image

from flash
OFF to load user hardware1

from flash

Table 8.

SW4 DIP Switch Default Settings (Board Bottom)

Switch

Board Label

Function

Default Position

RZQ_B2M

ON for setting RZQ resistor

of Bank 2M to 99.17 Ohm

OFF

continued...

3. Development Board Setup

UG-20046 | 2018.07.20

Intel

Stratix

10 GX FPGA Development Kit User Guide

Содержание Stratix 10 GX FPGA


































































































Результаты поиска

Содержание Stratix 10 GX FPGA

Отзывы:

Похожие инструкции для Stratix 10 GX FPGA

Бренды по названию

Популярные бренды

Altera Stratix 10 GX FPGA, Руководство пользователя

Результаты поиска

Содержание Stratix 10 GX FPGA

Отзывы:

Похожие инструкции для Stratix 10 GX FPGA

Бренды по названию

Популярные бренды