manualshive.com logo in svg

Altera JESD204B IP CORE, Руководство пользователя

Поделиться
Скачать
Altera JESD204B IP CORE Скачать руководство пользователя страница 82

JESD204B IP Core Design Guidelines

5

2015.05.04

UG-01142

Subscribe

Send Feedback

This section describes the design example included with the IP core and some implementation guidelines.

JESD204B IP Core Design Example

The design example entity consists of various components that interface with the JESD204B IP core to

demonstrate the following features:
• single or multiple link configuration

• different LMF settings with scrambling and internal serial loopback enabled

• interoperability against diverse converter devices

• dynamic reconfiguration
You can use the synthesizable design example entity in both simulation and hardware environments. 

Figure 5-1

 illustrates the high level system architecture of the JESD204B IP core design example.

©

 2015 Altera Corporation. All rights reserved. ALTERA, ARRIA, CYCLONE, ENPIRION, MAX, MEGACORE, NIOS, QUARTUS and STRATIX words and logos are

trademarks of Altera Corporation and registered in the U.S. Patent and Trademark Office and in other countries. All other words and logos identified as

trademarks or service marks are the property of their respective holders as described at

 www.altera.com/common/legal.html

. Altera warrants performance

of its semiconductor products to current specifications in accordance with Altera's standard warranty, but reserves the right to make changes to any

products and services at any time without notice. Altera assumes no responsibility or liability arising out of the application or use of any information,

product, or service described herein except as expressly agreed to in writing by Altera. Altera customers are advised to obtain the latest version of device

specifications before relying on any published information and before placing orders for products or services.

ISO

9001:2008

Registered

www.altera.com

101 Innovation Drive, San Jose, CA 95134

Содержание JESD204B IP CORE































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды