manualshive.com logo in svg

Altera JESD204B IP CORE, Руководство пользователя

Поделиться
Скачать
Altera JESD204B IP CORE Скачать руководство пользователя страница 27

Adding External Transceiver PLL

The JESD204B IP core variations that target an Arria 10 FPGA device require external transceiver PLLs

for compilation.
JESD204B IP core variations that target a V-series FPGA device contain transceiver PLLs. Therefore, no

external PLLs are required for compilation.
You are recommend to use an ATX PLL or CMU PLL to get a better jitter performance.
Note: The PMA width is 20 bits for Hard PCS and 40 bits for Soft PCS.

Related Information

Arria 10 Transceiver PHY User Guide

More information about the Arria 10 transceiver PLLs and clock network.

Timing Constraints For Input Clocks

When you generate the JESD204B IP core variation, the Quartus II software generates a Synopsys Design

Constraints File (

.sdc

) that specifies the timing constraints for the input clocks to your IP core.

When you generate the JESD204B IP core, your design is not yet complete and the JESD204B IP core is

not yet connected in the design. The final clock names and paths are not yet known. Therefore, the

Quartus II software cannot incorporate the final signal names in the 

.sdc

 file that it automatically

generates. Instead, you must manually modify the clock signal names in this file to integrate these

constraints with the timing constraints for your full design.
This section describes how to integrate the timing constraints that the Quartus II software generates with

your IP core into the timing constraints for your design.
The Quartus II software automatically generates the 

altera_jesd204.sdc

 file that contains the JESD204B IP

core's timing constraints.
Three clocks are created at the input clock port:
• JESD204B TX IP core:

•

txlink_clk

•

reconfig_to_xcvr[0]

 (for Arria V, Cyclone V, and Stratix V devices only)

•

reconfig_clk

 (for Arria 10 device only)

•

tx_avs_clk

• JESD204B RX IP core:

•

rxlink_clk

•

reconfig_to_xcvr[0]

 (for Arria V, Cyclone V, and Stratix V devices only)

•

reconfig_clk

 (for Arria 10 device only)

•

rx_avs_clk

In a functional system design, these clocks (except for 

reconfig_to_xcvr[0]

 clock) are typically

provided by the core PLL.

UG-01142

2015.05.04

Adding External Transceiver PLL

3-13

Getting Started

Altera Corporation

Send Feedback

Содержание JESD204B IP CORE































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды