Altera JESD204B IP CORE Скачать руководство пользователя | Manualshive

Страница: 48 / 158

background image

The realignment rules for lane alignment are similar to frame alignment:
• If two successive and valid /A/ characters are detected at the same position other than the assumed end

of multi-frame—without receiving a valid/invalid /A/ character at the expected position between

two /A/ characters—the receiver aligns the lane to the position of the newly received /A/ characters.

• If a recent frame alignment causes the loss of lane alignment, the receiver realigns the lane frame—

which is already at the position of the first received /A/ character—at the unexpected position.

ILAS Data

The JESD204 RX IP core captures 14 octets of link configuration data that are transmitted on the 2

nd

multi-frame of the ILAS phase. The receiver waits for the reception of /Q/ character that marks the start of

link configuration data and then latch it into ILAS octets, which are per lane basis. You can read the 14

octets captured in the link configuration data through the CSR. You need to first set the

csr_ilas_data_sel

register to select which link configuration data lane it is trying to read from. Then,

proceed to read from the

csr_ilas_octet

register.

Initial Lane Synchronization

The receivers in Subclass 1 and Subclass 2 modes store data in a memory buffer (Subclass 0 mode does not

store data in the buffer but immediately releases them on the frame boundary as soon as the latest lane

arrives.). The RX IP core detects the start of multi-frame of user data per lane and then wait for the latest

lane data to arrive. The latest data is reported as RBD count (

csr_rbd_count

) value which you can read

from the status register. This is the earliest release opportunity of the data from the deskew FIFO (referred

to as RBD offset).
The JESD204 RX IP core supports RBD release at 0 offset and also provides programmable offset through

RBD count. By default, the RBD release can be programmed through the

csr_rbd_offset

to release at

the LMFC boundary. If you want to implement an early release mechanism, program it in the

csr_rbd_offset

register. The

csr_rbd_offset

and

csr_rbd_count

is a counter based on the link clock

boundary (not frame clock boundary). Therefore, the RBD release opportunity is at every four octets.

UG-01142

2015.05.04

ILAS Data

4-11

JESD204B IP Core Functional Description

Altera Corporation

Send Feedback

«
...
46
47
48
49
50
...
»

Содержание JESD204B IP CORE































































































































































Отзывы:

Нет отзывов

Похожие инструкции для JESD204B IP CORE

Бренд: Zonet Страницы: 8

Бренд: NETGEAR Страницы: 2

Wireless Mini PCI Module

Бренд: E-Tech Страницы: 42

Бренд: C-Data Страницы: 26

Fieldpoint cFP-RTD-124

Бренд: National Instruments Страницы: 15

Бренд: Jøtul Страницы: 20

Бренд: Supermicro Страницы: 27

Бренд: ADTRAN Страницы: 4

Бренд: Variscite Страницы: 17

Бренд: Nexxt Страницы: 2

Бренд: NetCommWireless Страницы: 28

Бренд: LevelOne Страницы: 10

Бренд: SET Страницы: 38

Бренд: Allied Telesis Страницы: 2

Бренд: Planet Страницы: 431

Бренд: NetApp Страницы: 10

Бренд: Asus Страницы: 70

Бренд: Asus Страницы: 56

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды