Altai Technologies A8 Скачать руководство пользователя страница 2 | Manualshive

Страница: 2 / 24

background image

Altai Technologies Ltd. All rights reserved

A8 Installation Guide_ R3 Hardware Platform

TPS13-010_rev1.0

Copyright © 2007 Altai Technologies Limited

ALL RIGHTS RESERVED.

Altai Technologies Limited

Unit 209, 2/F,

East Wing, Building 17,

Hong Kong Science Park,

Shatin, New Territories,

Hong Kong

Telephone: +852 3758 6000

Fax: +852 2607 4021

Web:

www.altaitechnologies.com

Customer Support Centre:

Email:

[email protected]

Radio Frequency Interference Requirements

This device complies with Part 15 of FCC Rules.

Operation is subject to the following conditions:

1.

This device may not cause harmful interference.

2.

This device must accept any interference received, including interference
that may cause undesired operation.

3.

This device should not be co-located or operating in conjunction with any
other antenna or transmitter.

Interference Statement

This equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference in a residential installation.

«
1
2
3
4
...
»

Содержание A8

























Отзывы:

Нет отзывов

Похожие инструкции для A8

Бренд: H3C Страницы: 34

Бренд: Compaq Страницы: 112

RouterBOARD SXT 5HnD

Бренд: MikroTik Страницы: 2

Бренд: APARIAN Страницы: 2

Бренд: ZALMAN Страницы: 9

BIC 1I12-P2A25-M30MI1-BPX05-110

Бренд: Balluff Страницы: 12

Бренд: CAP-XX Страницы: 8

Бренд: Z Microsystems Страницы: 51

Бренд: Moxa Technologies Страницы: 51

ELITENAS EN104L+(B)

Бренд: Sans Digital Страницы: 9

Бренд: Idis Страницы: 17

IGS-5225-20T4C2X

Бренд: Planet Страницы: 16

Бренд: iGateWeb.com Страницы: 6

Бренд: Axis Страницы: 98

Бренд: Hama Страницы: 25

Бренд: Infoblox Страницы: 16

CyberSWITCH CSX101

Бренд: Cabletron Systems Страницы: 72

Бренд: B+B SmartWorx Страницы: 50

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды