Altai Technologies A8 Скачать руководство пользователя страница 5 | Manualshive

Страница: 5 / 24

Altai Technologies A8 Скачать руководство пользователя страница 5

Altai Technologies Ltd. All rights reserved

A8 Installation Guide_ R3 Hardware Platform

TPS13-010_rev1.0

1.

Introduction

This guide is designed to provide  the information needed to mount  A8 base station
(BTS) and A8 antennas at the site location.
The document is applicable for hardware platform A8 R3and the following models.

Product name:

A8 Super WiFi Base Station

Model number:

WA8011A-A

It is assumed in this document that a site survey has been performed before the site
installation. The appropriate antenna pole and BTS locations have been selected. It is
a good practice to have a document consists of a map and drawing illustrating the
base station and poles locations, antenna bearing/down-tilt, antenna height, etc… A
planning on IP network is also an important issue for network planning.

The  user  may  need  to  refer  the  following  document  during  A8  installation  and
Configuration.

[1] A8 Cable Connection Guide
[2] A8 Configuration Manual
[3] A8 Super WiFi Base Station Data Sheet

2.

A8 Base Station Outlook

Figure 2-1 Front View of A8 Base Station

«
...
3
4
5
6
7
...
»

Содержание A8

























Отзывы:

Нет отзывов