76
-EN
01GB06INA-W900E.fm
ALPINE INA-W900E 68-16909Z25-A (EN)
Depending on the response characteristics of the speaker, care should be
taken when setting the response slope of the high range speaker to
FLAT in 2.2ch (3WAY) mode (see “Adjusting the Crossover Settings
(X-OVER)” on page 74), as speaker damage may result.
Setting item: TW Setup
Touch
[
]
or
[
]
of TW Setup to select Factory’s or
User’s.
•
The TW Setup mode can only be selected if the FRONT/REAR/
SUBW. (4.2CH)/3WAY (2.2CH) switch on the IMPRINT audio
processor (PXA-H100) is set to 3WAY (2.2CH).
Storing Settings in the Memory
Adjustment or setting contents of X-Over, T.Corr and P/G-EQ can be
stored.
Contents that can be stored vary depends on the audio processor used.
1
Check whether the DEFEAT mode is OFF.
2
Touch
[MEMORY]
on the A.PROCESSOR list
display.
3
Within 5 seconds, touch any one of the preset
buttons
[P.SET 1]
through
[P.SET 6]
on the
A.Processor list screen.
The setting contents are stored.
•
The stored contents will not be deleted even when the battery power
cord is detached.
•
This operation cannot be performed when a typical equalizer setting
(e.g. Pops) is selected in “Equalizer Presets (F-EQ)” (page 75).
Calling up the Preset Memory
1
Check whether the DEFEAT mode is OFF.
2
Touch any one of the preset buttons
[P.SET 1]
through
[P.SET 6]
on the A.Processor list display to
select the preset memory.
•
It takes a few moments to call up the preset memory.
Setting the Subwoofer
1
Touch
[SETUP]
on the source selection screen.
The SETUP main screen is displayed.
2
Touch
[AUDIO SETUP]
.
The Audio Setup screen appears.
3
Touch
[
]
or
[
]
of SUBWOOFER to set the
subwoofer ON/OFF.
4
Touch
[
]
of SUBWOOFER after setting the
Subwoofer to ON.
The Subwoofer Setup screen appears.
Setting items: LEVEL / PHASE
*
/ SYSTEM / CHANNEL
*
* Only when Mult EQ OFF mode is selected.
Touch
[
]
or
[
]
of LEVEL to adjust the Subwoofer
output.
Setting range: 0 to 15
Touch
[
]
or
[
]
of PHASE to select 0° or 180°.
The subwoofer output phase is toggled SUBWOOFER NORMAL (0°)
or SUBWOOFER REVERSE (180°).
When the subwoofer is on, you can select either System1 or System2
for the desired subwoofer effect.
Touch
[
]
or
[
]
of SYSTEM to select SYSTEM 1 or
SYSTEM 2.
You can set the subwoofer output to stereo or monaural. Make sure to
set the correct output for your subwoofer type.
Touch
[
]
or
[
]
of CHANNEL to select STEREO or
MONO.
Setting the Response Slope for the High
Range Speaker (TW Setup)
Factory’s:
As protection from possible speaker damage, FLAT
cannot be set for the response slope of the high
range speaker in 2.2ch (3WAY) mode.
User’s:
The FLAT setting is possible in 2.2ch (3WAY) mode.
Adjusting the Subwoofer Level
Setting the Subwoofer Phase
Setting the Subwoofer System
SYSTEM 1 :
Subwoofer level changes according to the main
volume setting.
SYSTEM 2 :
Subwoofer level change is different from the main
volume setting. For example, even at low volume
settings, the subwoofer is still audible.
Setting the Subwoofer Channel
STEREO:
Subwoofer stereo (L/R) output
MONO:
Subwoofer monaural output
01GB00INA-W900E.book Page 76 Monday, September 13, 2010 9:52 AM