19
-EN
MobileHub™ Link
Operation(Optional)
About MobileHub™ Link
Connect a separately sold junction box and a portable telephone
(available from Nokia) to control the incoming and outgoing calls of
the portable telephone.
Caution
Even with hands-free operation, a driver can be distracted during
telephone operation or receiving a call. For the sake of safety,
drivers are requested to refrain from operating the telephone while
driving.
For the sake of safety, only incoming calls and Speed-Dial
outgoing calls can be operated.
• If a portable telephone is connected, its address book, incoming
and outgoing history are downloaded to the junction box.
• Please refer to the instruction manual of the junction box.
Telephone Mode ON/OFF
1
Press and hold
BAND/TEL.
for at least 2 seconds
to turn on the Telephone mode.
To turn off, press
BAND/TEL
.
See relevant pages for each item.
• Press and hold
BAND/TEL.
for at least 2 seconds. If a portable
telephone is not connected, “NO PHONE” is displayed for about 2
seconds, then the mode returns to the original source mode.
• When the portable telephone is taken off the junction box during an
incoming or outgoing call, or during a hands-free call, the call will
be treated as an ordinary one by the portable telephone.
• When there is an incoming call while the power of CDA-9820XM is
off, the power of CDA-9820XM will turn on automatically for a
hands-free call.
• Even if the power of the portable telephone is off, when CDA-
9820XM is set to Telephone mode, the power of the portable
telephone will be turned on.
• Even if the ACC power of the vehicle is turned off (even if the
engine is stopped) during a hands-free call, the call is not
disconnected, and an ordinary call by the portable telephone is
possible.
• If there is an incoming call during operation (except an outgoing
call or talking), operation mode will end and switch to the
incoming or talking mode.
Preset buttons
(1 through 6)
BAND/
TEL.
f
g
Rotary encoder
SEARCH/QS
F/SETUP
-
/
J
9
8
DISP/
TITLE
• An outgoing call from a portable telephone is also possible.
However, you cannot perform different operations at the same time
from a portable telephone and CDA-9820XM as malfunction can
result.
• With a junction box connected outgoing, incoming, and sending
history will also be recorded in the portable telephone.
• While telephoning, defeat is set to ON. When the call has finished,
the unit returns to your previous setting.
• The telephone volume can be adjusted on the CDA-9820XM. The
volume you set during the call is memorized, and is automatically
applied again on the next call.
• While telephoning or receiving incoming calls, press
DISP/TITLE
to show the Network Operator display for 5 seconds.
Incoming Calls
1
Press
:
/
J
to receive an incoming call.
2
Press
BAND/TEL.
to finish a call.
Telephone mode will end and return to the original source
mode.
• When the Automatic Calling mode is on, you can talk after 3
seconds of receiving the incoming call. (see “Setting the Automatic
Calling” on this page.)
Setting the Automatic Calling
The incoming call can be switched to Automatic Calling or Manual
Calling.
1
Press and hold
F/SETUP
for at least 3 seconds.
2
Select the TEL mode by pressing
g
or
f
.
3
Press
BAND/TEL.
to change to TEL AUTO or TEL
MANU.
4
Press
F/SETUP
to return to normal mode.
• Press
BAND/TEL.
during an incoming call to disconnect it.
• The initial setting of the factory is TEL MANU.
Calling
Calling by the address book
You can call up the address book registered in the portable telephone
to call from.
1
Press and hold
BAND/TEL.
for at least 2 seconds.
2
Press
SEARCH/QS
to select PHONE BK (Phone
Book) mode.
A list in alphabetic order is displayed.
Retrieving an addressee by Alphabetic Sort List
3
When displaying the Alphabetic Sort List, turn the
Rotary encoder
or press
g
or
f
to select
the addressee.
4
Press
:
/
J
or
Rotary encoder
to place a call.
5
Press
BAND/TEL.
to end the call.
Telephone mode will end and return to the original source
mode.
