Alpha InTec 50CS Скачать руководство пользователя страница 7

Страница: 7 / 32

INS

TALL

ATI

MAINTEN

Alpha Intec 50CS

- Position the smaller Easy-Flue 40 mm clamp

(with seal) supplied, over the bend. Fit the bend

to the boiler and rotate to the correct position.

Secure in position using the clamp. Ensure the

clamp is located centrally over both the bend

and boiler adaptor.

- Fit the inside (white) flue sealing collar over the

Easy-Flue. If it was not previously fitted, fit the

outside (black) flue sealing collar onto the flue

immediately before the terminal grille onto the

location provided.

- Slide the larger Easy-Flue 45 mm clamp over

the outer duct and pull the flue assembly

towards the bend, locating the inner duct into

the seal joint on the bend. Ensure the labels

marked 'TOP' are positioned at the top before

securing the flue assembly to the bend with the

clamp (three screws) located centrally over the

joint.

Fig. 1-9 - Rear flue

Note:

Check the flue terminal protrudes 120

mm out of the wall and the inner duct of the

terminal is positioned correctly (see Fig. 1-9).

- Make good the inside wall by pushing the

inside flue sealing collar upto the wall.

1.7 REdUCING THE FLUE - FIG. 1-10

When the flue length required is less than the

minimum stated in Section 1.6, paragraph 1,

refer to Fig. 1-10.
Discard the first telescopic section (not the

section with the terminal) of the Easy-Flue

1000 mm or 500 mm and cut to the required

length.
Note: Ensure that all cuts are square and free

from burrs.

Once assembled with the components pushed

home, the flue is fully sealed.

Fig. 1-10

Allow 20 mm

30 mm

Do not cut past this point

120

Inner duct

End of outer duct

Elbow seal joint

90° bend

Easy-Flue 40 mm clamp
and seal

Easy-Flue 45 mm clamp

Terminal

Flue sealing collar

Note:

Ensure the outer flue duct is horizontal

Side of boiler

CD Easy-Flue

Ensure the inner duct within
the terminal is at the top.

The inner duct must

be positioned to slope towards
the boiler

Note:

Inner duct seal

307

210

This dimension will be greater
if the boiler is not against the wall

This dimension will be greater

if the boiler is not against the wall

Содержание InTec 50CS

































Результаты поиска

Содержание InTec 50CS

Отзывы:

Бренды по названию

Популярные бренды

Alpha InTec 50CS, Инструкции по установке, использованию и обслуживанию

Результаты поиска

Содержание InTec 50CS

Отзывы:

Бренды по названию

Популярные бренды