background image

OPERATION & ADJUSTMENT INSTRUCTIONS 

13 

IMPORTANT SAFETY INSTRUCTIONS FOR OWNER

 

• 

Understand all of the operating features of your door control system at the time of its 

installation.  Your installing dealer will demonstrate them for you. 

• 

NEVER let children operate or play with door controls.  Keep the Remote Control away from 

children.  

 

• 

ALWAYS keep a moving door in sight and keep people and objects away from the door area 

until the door is completely closed.  NO ONE SHOULD CROSS THE PATH OF A MOVING 

DOOR.  

• 

TEST THE DOOR OPENER’S REVERSING FEATURE (where applicable) MONTHLY.  The 

door MUST reverse upon contact with a 4” high object on the floor.  After adjusting the 

force setting (clutch) or the limit of travel, ALWAYS RETEST the Opener.  Failure to ADJUST 

THE OPENER PROPERLY may result in SERIOUS INJURY OR DEATH.  

  

• 

To protect the motor protector from tripping - Do not exceed 10 door cycles per hour. 

• 

IMPORTANT:  The hardware box contains a caution label which states:  “This door is 

operated by a light duty operator.  To prevent the motor protector from tripping - Do not 

exceed 10 door cycles per hour.”  Permanently install this label adjacent to the door, near 

the push button station, at the eye height of the average adult, approximately six feet above 

the above the floor. 

• 

DO NOT over adjust the force setting (clutch) to compensate for a poorly working door. See 

page 18 for procedure to check the door operation and page 14 for proper clutch 

adjustment. 

• 

If possible, USE THE MANUAL RELEASE only when the door is closed.  Use caution when 

using the Release with the door open.  WEAK OR BROKEN SPRINGS MAY ALLOW THE 

DOOR TO CLOSE RAPIDLY, CAUSING SEVERE INJURY OR DEATH.  

• 

KEEP THE GARAGE DOOR PROPERLY BALANCED.  See the door owner's manual.  An 

improperly balanced door MAY CAUSE SEVERE INJURY OR DEATH.  Have a QUALIFIED 

SERVICE PERSON MAKE REPAIRS TO CABLES, SPRING ASSEMBLIES AND OTHER 

HARDWARE.  

• 

SAVE THIS INSTRUCTION MANUAL FOR END USER. 

• 

Inspect and maintain your door system as described in this manual. 

TO REDUCE THE RISK OF SEVERE INJURY OR 
DEATH: READ AND FOLLOW ALL INSTRUCTIONS!

 

WARNING 

FAILURE TO TEST REVERSING SYSTEM 
COULD RESULT IN DEATH OR SERIOUS 

INJURY.  TEST THIS SYSTEM ONCE A MONTH. 

 

WARNING

 

AVOID ELECTROCUTION:  

DO NOT ROUTE LOW VOLTAGE WIRES IN 

SAME CONDUIT AS HIGH VOLTAGE 

WIRES.  FOLLOW ALL LOCAL 

ELECTRICAL CODES OR THE NATIONAL 

ELECTRICAL CODE (NEC). 

 

WARNING

 

Содержание MH5011S





















Отзывы: