The purpose
of this booklet is to provide assembly,
installation and operation information concerning Allstar
Model MJ5011S & MH5011S (MS Series) Commercial
Vehicular Garage Door Operators and related Accessory
Products.
NOTICE
IT IS IMPORTANT THAT THIS INSTRUCTION
MANUAL BE READ AND UNDERSTOOD
COMPLETELY BEFORE INSTALLATION OR
OPERATION IS ATTEMPTED. IT IS INTENDED
THAT THE INSTALLATION OF THIS UNIT WILL BE
DONE ONLY BY PERSONS TRAINED AND
QUALIFIED IN THE INSTALLATION, ADJUSTMENT
AND SERVICE OF COMMERCIAL OVERHEAD
DOORS AND DOOR OPERATORS AND BY
QUALIFIED ELECTRICIANS.
NOTICE
THE IMPORTANT SAFEGUARDS AND
INSTRUCTIONS IN THIS MANUAL CANNOT
COVER ALL POSSIBLE CONDITIONS AND
SITUATIONS WHICH MAY OCCUR DURING ITS
USE. IT MUST BE UNDERSTOOD THAT COMMON
SENSE AND CAUTION MUST BE EXERCISED BY
THE PERSON(S) INSTAL- LING, MAINTAINING
AND OPERATING THE EQUIPMENT DESCRIBED
HEREIN. DO NOT USE THIS EQUIPMENT FOR
ANY OTHER THAN ITS INTENDED
PURPOSE - OPERATING OVERHEAD
COMMERCIAL VEHICULAR GARAGE DOORS.
STANDARD FEATURES
Solid State Controls:
The Allstar MJ5011S & MH5011S
operators employ solid state technology with advanced
standard features to provide for a complete commercial
door operating system.
Limit Switches:
Driven limit switches, easily adjusted
over a wide range. The motor may be removed without
affecting the limit switch adjustments.
Manual Release:
Permits manual operation of the door
in the event of a power failure. The Model MH511S is
equipped with a chain hoist to aid in manual operation.
Control Circuit:
Connection terminals for a standard
three button Open, Close and Stop control station at 5 Volts
DC. The motor control board features a built-in 3 button
station for test purposes.
Connections For Auxiliary Entrapment Protection
Devices:
For the ultimate in protection, terminals are
provided to connect an Allstar Safe-Finish™ or Access
Alliance Safe-Finish II™ monitored photo-beam system.
Additional connection terminals for a Normally Open and
Normally Closed reversing devices such as foam or
pneumatic reversing door edge components or a three wire
photo-beam are provided.
Constant Contact To Close:
Standard operating mode
(C2), programmable to Momentary Contact To Close (B2)
and four additional operational modes.
MS SERIES DOOR OPERATOR APPLICATIONS:
Jackshaft operators are intended for commercial and
industrial use to raise or lower sectional overhead doors
by chain coupling or direct coupling to the door shaft.
Jackshaft operators are suitable where all or part of the
door remains in a vertical position when fully open such as
doors with at least 18 inches of lift clearance or full vertical
lift doors. MS Series Jackshaft operators may also be
used with certain roll up service doors and grills when
appropriately sprocketed (consult factory).
A jackhaft operator
DOES NOT LOCK THE DOOR IN ITS
CLOSED POSITION.
However, because the cross-header
shaft is prevented by the operator from turning, the torsion
springs provide no assistance in lifting the door should an
attempt be made to raise it manually.
The MS Series jackshaft operators are used in the
following applications:
-
Intermittent Duty, Limited Cycle Commercial
installations only
-
Rate of operation shall not exceed 10 cycles of
opening and closing per hour, maximum 60 cycles
per day.
-
Indoor Use Only
-
Up to 14 foot high doors with a maximum area of
196 square feet, maximum area slightly higher for
lighter doors - consult factory
-
Use with foam/pneumatic reversing door edge or
photoelectric device - REQUIRED where the 3-
button station is out of sight of the door, or
any
other automatic, remote or manual control is used
to activate the door
OPTIONAL FEATURES:
Digital Radio Controls:
Open, Close and Stop
operation. Radio units are available to control up to 27
doors from one transmitter.
Timer to Close Operation:
Two of the
programmable operation modes (T & TS), closing delay is
adjustable from 5 seconds (factory set at 30 seconds) to
5 minutes in five second intervals.
Delay on Reverse
:
Factory set to 0.6 seconds,
adjustable to 2 seconds.
Keyless Entry System:
Connection terminals
provided for hard wired or wireless keyless entry systems.
PRODUCT FEATURES
3
