manualshive.com logo in svg

Allison B 300, Руководство по устранению неисправностей

Поделиться
Скачать
Allison B 300 Скачать руководство пользователя страница 367

 

Copyright © 1998 General Motors Corp.

P–11

 

W T E C   I I   E L E C T RO N I C   C O N T RO L S   T RO U B L E S H O OT I N G   M A N UA L

 

APPENDIX P — INPUT/OUTPUT FUNCTIONS

 

WARNING!

 

These schematics show the intended use of the specified controls features which
have been validated in the configuration shown. Any miswiring or use of these
features which differs from that shown could result in damage to equipment or
property, personal injury, or loss of life. ALLISON TRANSMISSION IS NOT
LIABLE FOR THE CONSEQUENCES ASSOCIATED WITH MISWIRING
OR UNINTENDED USE OF THESE FEATURES.

 

FIRE TRUCK PUMP MODE

 

USES:

 

Facilitates engagement of split shaft PTO and shifts transmission to fourth range lockup.

 

VARIABLES TO SPECIFY:

 

None

 

VOCATIONS:

 

Fire Truck Pumpers

 

SYSTEM OPERATION

 

OPERATOR ACTION — System Response

 

TO ENGAGE:

 

1.

 

SELECT NEUTRAL

 

 — Transmission shifts to Neutral.

2.

 

APPLY PARKING BRAKE

 

 — None

3.

 

SELECT PUMP

 

 — Turns on “Pump Mode Requested” light. Stops output shaft rotation. When split-shaft 

engages, PPE signal and “Pump Engaged” light are turned on. Transmission output unlocks.

4.

 

SELECT DRIVE

 

 — Transmission shifts to fourth lockup. “OK To Pump” light is turned on.

 

TO DISENGAGE:

 

1.

 

SELECT NEUTRAL

 

 — Transmission shifts to Neutral if output rpm < 1000.

2.

 

SELECT ROAD MODE

 

 — Stops output shaft rotation. PTO disengages. Transmission shifts back to Neutral.

 

Figure P–11. Fire Truck Pump Mode

 

WARNING!

 

If this function is enabled in the shift calibration, the function MUST be integrated
into the vehicle wiring. If the function is available in the shift calibration but will
not be used in the vehicle, it MUST be disabled in the calibration.

V05016

WIRE  118

FIRE  TRUCK

PUMP  MODE  INPUT

PARKING  BRAKE

PRESSURE  SWITCH

Switch is closed

when brakes are on

POSITIVE  PUMP

ENGAGEMENT
(PPE)  SWITCH

Switch is closed

when pump

is engaged

WIRE  161B  SIGNAL  GROUND

WIRE  114  RANGE  INDICATOR = 4th

WIRE  117  PUMP  ENABLE

DASH  SWITCH

Open: Road

Closed: Pump

Relay shown de-energized

PUMP

ENGAGED

SWITCHED

POWER

A2

NC

COM

VIM

NO

A3

OK  TO

PUMP

PUMP  MODE

REQUESTED

SPLIT-

SHAFT

PTO

AIR

13

2

16

ECU

VIW

CONNECTOR

Содержание B 300













































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды