manualshive.com logo in svg

Allison B 300, Руководство по устранению неисправностей

Поделиться
Скачать
Allison B 300 Скачать руководство пользователя страница 347

 

Copyright © 1998 General Motors Corp.

L–1

 

W T E C   I I   E L E C T RO N I C   C O N T RO L S   T RO U B L E S H O OT I N G   M A N UA L

 

APPENDIX L — EXTERNALLY-GENERATED ELECTRONIC INTERFERENCE

 

1–1.

ELECTROMAGNETIC/RADIO FREQUENCY INTERFERENCE

 

All electrical and electronic systems generate electromagnetic fields that can interfere with other electronic 
systems. Allison Transmission electronic transmission controls comply with Federal Communications Commission 
(FCC) regulations and other guidelines concerning emitted radio frequency interference for transportation 
electronics. The position of Allison Transmission Division of General Motors is that manufacturers and installers 
of EMI/RFI emitting equipments are responsible for adhering to FCC regulations and other guidelines concerning 
emitted radio frequency interference for transportation electronics.

Some radio-telephone or two-way communication radios (land-mobile radio), or the manner in which they are 
installed, can adversely affect vehicle operation or be affected by other vehicle components. Expenses incurred to 
protect vehicle-related systems from EMI/RFI emissions by radio-telephone or two-way communications radios 
(land-mobile radio) or to integrate such devices into vehicles are not the responsibility of Allison Transmission. 

 

1–2.

GENERAL GUIDELINES FOR RADIO EQUIPMENT INSTALLATION 

 

The following general guidelines for installing radio-telephone or two-way communications radios (land-mobile 
radio) in a vehicle supplement, but DO NOT replace, detailed instructions provided by the radio equipment 
manufacturer. Detailed installation instructions are the sole responsibility of the radio equipment manufacturer.

Experience has shown that most EMI/RFI problems can be prevented or eliminated by following the guidelines.
If EMI/RFI problems persist after following the guidelines and after ensuring the installation conforms to the 
guidelines, contact the vehicle and radio equipment manufacturers for additional installation or equipment 
operation instructions.

 

A.

Transmitter Installation

 

1. Locate remote radio transmitters as far away from other electronic devices and as near to the side 

of the vehicle body as possible.

2. Mount transceivers (transmitter and receiver in one box) under the dash so as not to interfere with 

vehicle controls or passenger movement.

 

B.

Antenna Installation

 

Each vehicle and body style react differently to radio frequency energy.  When dealing with an 
unfamiliar vehicle, test various antenna locations by using a magnetic mount antenna and checking 
for adverse effects.  Antenna location is a major factor in EMI/RFI problems.

 

C.

Antenna Cable Routing

 

1. Use high quality, 95 percent shield coverage, coaxial (coax) cable. Route the coax well away from 

any electronic components.

2. Route antenna cables as far away from vehicle wiring as possible to reduce the likelihood of the 

vehicle wiring acting as an antenna for interference.

 

D.

Radio Wiring and Connector Location

 

1. Connect transmitter power leads directly to the battery.

2. For transceivers (transmitter and receiver in one box) with ignition control, place a 12V power 

contactor at the vehicle battery. Drive the contactor coil, through an appropriate in-line fuse, from 
an ignition circuit not powered during engine cranking.

Содержание B 300













































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды