manualshive.com logo in svg

Allison B 300, Руководство по устранению неисправностей

Поделиться
Скачать
Allison B 300 Скачать руководство пользователя страница 280

Copyright © 1998 General Motors Corp.

E–43

W T E C   I I   E L E C T RO N I C   C O N T RO L S   T RO U B L E S H O OT I N G   M A N UA L

APPENDIX E — CONNECTOR PART NUMBERS, TERMINAL PART 

NUMBERS, TOOL PART NUMBERS, AND REPAIR INSTRUCTIONS

1–11. DEUTSCH DT SERIES CONNECTORS (12-WAY NAVISTAR VIW)

A.

Connector/Terminal Repair

B.

Terminal Removal (refer to Figure E–12, Views A and B)

1. Use a small-bladed screwdriver with an added notch (as shown in View B) to remove the locking 

wedge that holds the terminals in place.

2. Use a small screwdriver to remove the 12-way seal plug from the rear of the connector plug or 

receptacle and slide the seal up the wires out of the way, temporarily. 

3. Use a small screwdriver to release the locking lever for the individual terminals that need attention. 

Pull the wire and terminal out the rear of the connector.

4. If replacing the terminal, cut the wire through the middle of the terminal crimp to minimize wire 

loss.

C.

Terminal Crimping (refer to Figure E–11, View C)

1. Strip approximately 6–8 mm (0.236–0.315 inch) of insulation from the wire.

2. Set the crimping tool wire size to number 18. To set the wire size, remove the retainer pin. Lift and 

rotate the indicator until 18 is aligned with the SEL NO. arrow. Reinstall the retainer pin.

3. Insert the contact end of the terminal down into crimping tool J 34182. Adjust the crimping tool 

depth by loosening the locking ring until the depth adjusting screw is free and turning the adjusting 
screw until the wire end of the terminal is just above flush with the top of the crimping hole. The 
crimp jaws will now contact the middle of the terminal barrel. Tighten the lock ring to retain the 
adjustment.

Crimping Tool

J 34182

Use

Description

P/N

Vehicle Interface

12-Way Plug (Gray)
Terminal, Socket
Wedge Lock
Cavity Plug

29511372
29511366
29511400
23016504

12-Way Receptacle (Gray) 
Terminal, Pin
Wedge Lock
Cavity Plug

29511754
23018768
29511401
23016504

12-Way Plug (Black)
Terminal, Socket
Wedge Lock
Cavity Plug

29511373
29511366
29511400
23016504

12-Way Receptacle (Black)
Terminal, Pin
Wedge Lock
Cavity Plug

29511755
23018768
29511401
23016504

Содержание B 300













































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды